Re: Grounded Experimental Delta Printer
Thanks guys. I am sure trying. I have a radical redesign in the mix. I will be heading over to QU-BD today. They are going to help me laser-cut most of the design. Unfortunately, I don't get to reuse...
View ArticleRe: Grounded Experimental Delta Printer
... your head with two gears hold in plastic won't be stable enough - reread my post with the 2-store-'press-bearing' - you need a much more squeezed setup or the tool wont get enough rigidity with...
View ArticleRe: Grounded Experimental Delta Printer
VDX Wrote: ------------------------------------------------------- > ... your head with two gears hold in plastic won't > be stable enough - reread my post with the > 2-store-'press-bearing'...
View ArticleClik here to view.
Re: Grounded Experimental Delta Printer
Video Here is a rendering of my new design. I have just gotten back from QU-BD. They were generous enough to laser cut all my parts. I am now frantically printing out the remainder of the parts. (I...
View ArticleClik here to view.
Rostock X-Y-Z Scale Issues
I have worked out most all of the kinks with commissioning my Rostock Mini and am getting some really great prints. The only issue I am having is that the parts are coming out too large. The Empire...
View Articlerostock j-head bowden mounting
Hi all, I start construct Rostock printer and try find some good mounting on platform (original rostock) for j-head hotend and bowden pneumatic fitting Do you have some tips please? Thanks for your...
View ArticleRe: Rostock X-Y-Z Scale Issues
If your prints are square then you have entered the correct geometry. I would put money that the mm/step (or mm/revolution or etc) setting for each stepper is off. Even if it is right, you should be...
View ArticleRe: Rostock X-Y-Z Scale Issues
My prints are perfectly square and perfectly straight. I followed Steve Graber's instructions on YouTube for leveling and changed the DELTA_EFFECTOR_OFFSET to tune out my cupped travel, that seemed to...
View ArticleRe: Rostock X-Y-Z Scale Issues
For some reason this has been stuck in my mind and I finally figured out why. 227/200 is extremely close to 17/15. XL Timing belt pulleys often come with 17 or 15 teeth and GT2 belt pulleys often come...
View ArticleRe: Rostock X-Y-Z Scale Issues
You were right about my pulley settings being incorrect, I forgot that I purchased 40 tooth MXL pulleys, I thought I had 36 tooth GT2 pulleys. I set my steps per unit to 39.41 and now I'm dead on. Not...
View ArticleRe: Rostock X-Y-Z Scale Issues
I was so close. Glad you got it figured out. Happy printing.
View ArticleClik here to view.
Re: Grounded Experimental Delta Printer
SIMPSON'S FIRST PRINT Here is Simpson showing off his creations. I didn't print all at the same time. In fact, I won't be able to until I work on bed leveling issues. Left: 30mm/s, .3 layer height, no...
View ArticleRe: Grounded Experimental Delta Printer
Amazing! I never thought it would work so well. Well done for pulling it off.
View ArticleRe: Grounded Experimental Delta Printer
I didn't expect it to be this good at this point. I always expected it to work but I was doubtful that it would be able to do high quality prints. I have about 5 optimization that I am going to throw...
View ArticleRe: Grounded Experimental Delta Printer
Hi Nicholas, really well done! :)-D It shows, the stability of the head is good enough to stay in place with low torques. Next question - how fast can you go with some 'beefier' motors?
View ArticleRe: Grounded Experimental Delta Printer
VDX Wrote: ------------------------------------------------------- > Hi Nicholas, > > really well done! :)-D > > It shows, the stability of the head is good enough > to stay in place...
View Article