Re: Rostock problems
If manual positioning (G0 X0 Y0 Z5) moves head to the center then it is slicer settings. Make sure slicer knows that point X0 Y0 is in the center of heatbed.
View ArticleRe: Worm Drive Grounded Delta Printer
QuoteSolidus Labs It will be interesting to see if there is any difference in performance with the added horsepower of the due vs the Mega2650 Are you going to rewrite the Marlin Firmware to work with...
View ArticleRe: Various problems with Kossel Mini
I guess it's a problem with the probing-switch. Check if the triggered / open - states are correct. IIRC, the endstop should be triggered when the probe is deployed, and open when it hits the ground...
View ArticleRe: Kossel Calibration Problem
when it says z=0 and it is 5mm above the bed, the z-height in the firmware is 5mm too low. Try changing it to +5mm, but approach slowly to z=0 then ;-)
View ArticleRe: Worm Drive Grounded Delta Printer
I have had a ramps-fd and due on my desk for a while but I have not had the time to do any hacking with it. It doesn't look like anyone else has put much effort into porting marlin to due because lack...
View ArticleRe: Worm Drive Grounded Delta Printer
APrinter firmware looks nice (tu) Packed gcode working with APrinter firmware It works very smoothly. On gcode produced by Cura I see a good 50% reduction in side. Concerning firmware performance, I...
View ArticleRe: Various problems with Kossel Mini
I ran into this issue with a Kossel-derivative that I built some time ago. Two things were causing the problem: The endtop logic for the probe was inverted from what it was supposed to be. So the...
View ArticleRe: Best Delta Controller??
Quoteumdpru Are you guys really getting 1/32 microstepping? Wasn't there some controversy with respect to truly getting even 1/16th on your typical reprap? How do you measure that you are getting to...
View ArticleRe: Worm Drive Grounded Delta Printer
Here is what I found about porting Marlin to Due, [github.com]
View ArticleX-Y Axis are moving but Z is not !!
Hello Im working on a Reprap Rostock 3d printer V1 and my current problem is, that somehow my x and y axis are movin but my z isnt reacting to any command(its also not getting too hot or something)....
View ArticleRe: Best Delta Controller??
Hi, just to be sure, the Ramps 1.4 are working fine with the Hall endstops right ?
View ArticleRe: Best Delta Controller??
QuoteTheCrey Hi, just to be sure, the Ramps 1.4 are working fine with the Hall endstops right ? Yup, works fine. A word of warning though, the connection between the little circuit board and the...
View ArticleRe: Best Delta Controller??
1/32 micro stepping currents are going to be really low. I just find it difficult to believe that 1/32 stepping is taking place without careful component matching. See here [hydraraptor.blogspot.com]...
View ArticleRe: RepRap 3DR Delta printer Released
Hi, starting to build a version too, i am using the bigger version from JEZZMUND by thingiverse.com. I am really looking forward to it. What boards are you using most ? I am still not sure what to...
View Articlea new extruder motor setup design to try out.
[reprap.org] also on thingiverse, [www.thingiverse.com] but it seems makerbot has made it not list in search results, it can only be found by direct link, or looking in extruder section. this design...
View ArticleRe: a new extruder motor setup design to try out.
Hi, i am new to this scene so i am not quite sure, but this is for a bowden extruder or ?
View ArticleRe: 3DR "Simple" Delta Printer
How is everyone mounting an LCD to their machine? I'm looking to mount mine to the top of mine since it's closest to the controller. I looked at Rich's github files and found an LCD adapter but I...
View ArticleJohan's Marlin - Delta Auto Bed Leveling
Hi Guys I'm looking to add auto bed levelling to my Cherry Pi design. I've printed out a new effector with the Allen key type probe and microswitch assembly and I've run the cable for it back through...
View ArticleRe: X-Y Axis are moving but Z is not !!
Hi Paul Have you tried your Z motor on another port and the Z port with another motor? Also check that the end stops are working by sending a M119 command as you click each one in turn check too that...
View Article