Re: 3DR "Simple" Delta Printer
Woops, I'd forgotten that the images are on a different server. They should be back online later today.
View ArticleMarlin + RAMBo: Unpredictable moves of the Z carriage;
Hi folks! I'm trying to commission a new Delta printer and am struggling with a problem wherein whatever motor attached to either of RAMBo's Z dual drivers will move the carriage at a faster rate than...
View ArticleRe: Marlin + RAMBo: Unpredictable moves of the Z carriage;
RAMBo only has one Z driver, it just has two connections to the same driver for when you want to drive two motors in parallel (such as with a Prusa Mendel-style printer). It seems like the Z driver...
View ArticleRe: RepRap 3DR Delta printer Released
Quotelandsharkxx How much does it cost to build this? You just might be able to build one of these for around $450. The cost is going to vary from person to person, as everyone makes different choices...
View ArticleRe: 3DR "Simple" Delta Printer
Printrbot.com has changed the parts used in the Simple in several places. They sell a new metal extruder that I do not have. I ordered the Simple kit without the wood frame so I could build a 3DR...
View ArticleRe: New Own Design Printer 'Cherry Pi'
They're expensive, but I'm curious to see advantages/disadvantages of using a pizza stone for the bed. :)
View ArticleRe: Marlin + RAMBo: Unpredictable moves of the Z carriage;
Cameron, Thank you very much for your help! This is exactly what was needed. All carriages now are moving uniformly. For the benefit of folks reading this later, the board was made by Geeetech and IS...
View ArticleRe: RepRap 3DR Delta printer Released
HI, is it possible to just make the printer higher ? I mean i have some 100cm rods here, could i just scale it higher without any issues ? I already did it a little big bigger in size but not...
View ArticleRe: New Own Design Printer 'Cherry Pi'
QuoteNewPerfection QuoteRickM The only thing I've not been able to find there is borosilicate glass. I'm having an absolute nightmare trying to get a 250mm round piece. The only place that has it is...
View ArticleRe: RepRap 3DR Delta printer Released
QuoteTheCrey is it possible to just make the printer higher ? I mean i have some 100cm rods here, could i just scale it higher without any issues ? RichRap's blog has your answer: QuoteRichRap "Is 3DR...
View ArticleRe: New Own Design Printer 'Cherry Pi'
QuoteRickM I'm in the UK. Sadly all the circular mirrors around here seem to be made of acrylic. Here you go: [www.amazon.co.uk] (tu)
View ArticleRe: RepRap 3DR Delta printer Released
Oh yeah... i read it about thousand times... sorry :) I am not planing to go so high, but i don't want to cut off the nice rods
View ArticleHoming in Marlin
Hello, I am hoping for a response with someone familiar with the Marlin code... (by this, I mean the Delta modifed Marlin code from Johann - its for a mini Kossel) My questions have to do with homing....
View ArticleRe: Homing in Marlin
Having nearly the same issue with mine. I had mine working well - then blew F2 fuse. Now, not working right on homing. But... When it was - Autohome was just issuing a G28 (AFAIK). Each axis would...
View ArticleRe: Mini Kossel - G28 Homing Problem
I'm having a similar issue. Video here of pressing "Home" [youtu.be]
View ArticleRe: Mini Kossel - G28 Homing Problem
Found my problem - Y and Z end probes were reversed on the board.
View ArticleRe: 3DR "Simple" Delta Printer
Interesting that they have a smaller motor for Y. My original Printrbot Simple had three small motors and one large motor. If you look at my construction motors, you can see that all three of my tower...
View Article