Re: 3DR "Simple" Delta Printer
Finally, after being distracted by repairing my Mini Kossel and a new delta drawing robot project........ My Blue 3DR Simple is working. First print today of 5mm pyramid. Only problem is that I do not...
View ArticleRe: 3DR "Simple" Delta Printer
Quotepsykhon Hi everybody! I started building a 3dr simple some time ago and yesterday it made its firsts couple of prints, post:3DR Simple (warning: its in spanish) just like to thank a lot to...
View ArticleRe: 3DR "Simple" Delta Printer
>>>>>>>>>>>>>>> To get the extruder to feed the correct amount of filament I had to set the M92 E value pretty high, I think somewhere near 700. The...
View ArticleRe: RepRap 3DR Delta printer Released
repetier-firmware vs marlin vs sailfish [forums.reprap.org]
View ArticleClik here to view.
Re: 3dr Motor control
Zacbot, Motor issues are fine now. I see why you went away from the fishing line for the drive. I'll most likely do that on an upgrade. I had an issue with the thermister shutting off, but I had a...
View ArticleRe: RepRap 3DR Delta printer Released
Many thanks for the link. The thread started October 16, 2012 and seems to compares the firmware for cartesian printers. It would be nice to know, if since that time, the actual repetier firmware...
View ArticleNEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Dear Reprappers and experts My first post (not the last off Corse) :) Finished from my build of a standard rostock with original dimension (RAMP 1.4 - INDUINO MEGA 2560 – MECHANICAL ENDSTOPS V1.2 –...
View ArticleRe: RepRap 3DR Delta printer Released
@hercek I've been trying today with the manual method, going through the notebook went well and things were converging up to a point where I started to oscillate. This would be fine, but the errors...
View ArticleRe: RepRap 3DR Delta printer Released
Found a similar issue.... But at the ends repetier said: QuoteRepetier To be fair, the radius correction is not mathematically correct. It only computes the column coordinate based on the correction...
View ArticleRe: RepRap 3DR Delta printer Released
And I must say, I choosed to build the 3DR, because of this matter. The frame is build with printed parts, so the error marge is very very small, compared to any hand made part. Most starter will not...
View ArticleRe: 3DR "Simple" Delta Printer
You should be able to plug the fan into the FAN connector on the Printrboard. This is a PWM output, which means it's controlled via software. Once you enable fan cooling in your slicer, it should...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
I am just building my own version of a delta, and am using repetier firmware which deos config slightly differently. However the issue you have seems to be familiar with many who build delta's, it is...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Basically the same as daveb500 said + I think you also need to comment out: #define ACCURATE_BED_LEVELING
View ArticleRe: RepRap 3DR Delta printer Released
When I talk about tower positions, I mean virtual tower positions. They may be wrong because of something of this is wrong: actual real tower position carriage dimensions platform dimensions...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
daveb500 / imyz many thanks for your replies i tried REPETIER and face same exact problem i cleared EEPROM nothing change if i invert the logic of my endstops it seems the result not as expected...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Hi LB-3D Your endstop configuration is working o.k although you seem to have your switches wired NO I.e they go closed circuit when you operate them. That's o.k though because you have the logic set...
View ArticleRe: RepRap 3DR Delta printer Released
Very good. And that s why, i said at the beginning of this discussion, "it is the last I will look after". I didn t say, "it is not worth to look at it". First check reflector, rods, carriage. And...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Do you have a thermistor connected? I cannot recall at the moment if the printer would run without the thermistor, if you have it defined in the firmware. Try to define the temp sensor ar 0 and try...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
HOOOOORAY!!!! ANDY U'R RIGHT - THANK YOU VERY MUCH - you saved me i didn't know that those jumper are related to stepper driver 8-) once installed - homing - and thats it :D homing very smoothly...
View Article