Re: Bed levelling on a Delta system, possible alternative?
Quotehercek Which source code are you trying to compile? The one from your git [github.com]
View ArticleRe: New Own Design Printer 'Cherry Pi'
Andy, Since you cherry picked several good ideas from other designs, I'm curious about your opinion on the spherical ball setup used on the SpiderBot effector plate. Instead of 6 spherical magnets,...
View ArticleRe: Worm Drive Grounded Delta Printer
.2 layer and .4 layer sample print [attachment 24630 DSE_4824.JPG]
View ArticleClik here to view.
Re: Building a 3DR "Simple"
You mean like this: Yes, it works and there are no balance problems. I have been thinking about designing a new one that orients the spool so it's facing the extruder, so I'll put that higher on my...
View ArticleRe: Building a 3DR "Simple"
There are a couple of reasons I went with RichRap's geared extruder. First, I was concerned that the direct-drive extruder wouldn't have enough force to push the filament through the Bowden tube. And...
View ArticleClik here to view.
Re: 3DR "Simple" Delta Printer
Tomek, I never finished that version of the parts, nor did I ever put them on Github, which is why you can't find them. I do have a triangular version I could put up there: I haven't tested this...
View ArticleRe: Bed levelling on a Delta system, possible alternative?
OK, I guess you want it because of the single point z-probe, i.e. you have a z-probe hardware mounted on your machine and want G29 not to do the matrix based bed leveling (which is what most Kossel...
View ArticleRe: Kossel with heated bed - how is it possible?
Hi, from where do you got your heater, because I am not located in the US, too. Maybe I will get the glass plate from there? Thanks, Subo
View ArticleRe: Bed levelling on a Delta system, possible alternative?
Quotehercek OK, I guess you want it because of the single point z-probe, i.e. you have a z-probe hardware mounted on your machine and want G29 not to do the matrix based bed leveling (which is what...
View ArticleClik here to view.
Re: Building a 3DR "Simple"
I've started an album of build pics: [plus.google.com] I'm rubberizing the bottom of the bottom end-caps with aerosol Plasti-dip. IMG_20140112_174544.jpg
View ArticleRe: Building a 3DR "Simple"
I'm planning on using a couple of Airtripper's "pipe.stl" tube guides and some PTFE tubing to guide the filament from the spool to the extruder. That should give me some flexibility in my spool...
View ArticleRe: New Own Design Printer 'Cherry Pi'
Hi vreihen I toyed with the spider bot design but gave it up in favour of the one I finally went with. I got my 10mm spherical magnets very cheap from firstformagnets.com in the UK. I am very happy...
View ArticleRe: Jazzabell - 3DR printer
Are your modifications to use magnets compatible with a stock 3DR? I'm building a 3DR after this 3DR "Simple" build is done and am thinking magnets are the way to go.
View ArticleClik here to view.
Re: 3DR "Simple" Delta Printer
I thought I'd share a progress report. I've completed printing all of the main frame pieces and started assembly, although I just ran out of M4 nuts, hence the top frame not being together &...
View ArticleRe: Delta-Pi "Flexing" hub
So, it isn't heat. The stepper driver chips are cool to the touch immediately after powering down, as are the stepper motors. The problem is not that the hot-end moves up and down as it crosses the...
View ArticleRe: Delta-Pi "Flexing" hub
I tried turning up the trim pots until the motors were very hot to the touch when running for a couple of minutes. Same problem, so not a low voltage issue. I have a new hypothesis. The motors I am...
View ArticleRe: 3DR "Simple" Delta Printer
Tomek, Are you referring to the original 3DR Delta files by RichRap aka Richard Horne? [github.com] And his blog has more details, he has published four updates and talked about different build...
View ArticleRe: Kossel with heated bed - how is it possible?
Hi,. i searched for kapton-heater or silicone-heater or something on ebay, then i found it. For the glass, i bought a spring-form with a glass bottom (really, for baking cake ;-)). It cost about 15€...
View ArticleRe: Building a 3DR "Simple"
I designed a plastic spool holder for the 3DR Simple. It works great in conjunction with:[www.thingiverse.com]. Just place it in the upper frame.
View ArticleClik here to view.
Re: Building a 3DR "Simple"
Today I've got the top pieces and the spools printed. IMG_20140113_133848.jpg I don't have the red filament I want to use for all the mechanical pieces yet, so I'm stalled until that arrives. :(...
View Article