Quantcast
Channel: Reprap Forum - Delta Machines
Browsing all 20291 articles
Browse latest View live
↧

Re: Rostock Printer build

Quotejaguarking11 Thank you very much. I love the suggestion of using Styrofoam first. I will be doing that soon. I am curious what is the height of yours from end stop to where the build plate lives....

View Article


Re: Rostock Printer build

Ah, that makes sense there. I am trying to build a platform that is stable enough to stand on, without the smooth rods attached. Torsional strength is where I personally think most of these printers...

View Article


Re: Rostock Printer build

Quotejaguarking11 IMHO the smooth rod should only be a carrier and not a support structure, I realize this is going against the design goal to have as few parts as possible, however I think its a...

View Article

Re: Which extruder to choose?

I'm testing on my delta Bulldog Lite E3d Hotend excellent economic solution

View Article

Re: Delta Vslot kossel mini

A video of the autolevel function using FSR Autolevel

View Article


Re: Auto level probe question (Kossel Mini)

That's helpful, thanks.

View Article

Auto Level problems

Hi, I took the challenge to build a Kossel myself. Thanks to all the stuff that can be found it is not as hard as I expected. But one thing that is bugging me now for several weeks is that I cannot...

View Article

Re: Rostock Printer build

I Started receiving my parts. Got the rod and the arduino/ramps1.4/polulu driver & lcd screen. Should be getting the plastic parts either today or tomorrow. Hopefully I get my bearings as well....

View Article


Re: Rostock Stepper Motor Problem - Help

Thanks for the advise. I wondering if may be a problem with the RAMPS board or Arduino. The Y tower is the one I am having problems with. The X and Z work fine. I can switch the Y and X tower's motor...

View Article


Re: Building a 3DR "Simple"

@Mallgan.O Aha, that is the problem. I have official Printrbot Board from Printrbot. It has their boatloader installed. Why is the one you have in the dropbox folder different? I would have to buy the...

View Article

Re: Rostock Stepper Motor Problem - Help

for me when i did not install jumpers on my ramps all motor did same noise did you check if there is damaged jumper under y stepper driver? regards

View Article

Re: Rostock Printer build

I have the Mechanical ones in the second link. Either is good for the job, they just wire up differently and configuring is different.

View Article

Kossel endstops

If the Kossel mini only uses 3 end stops why did my set of parts come with 6 holders?

View Article


Is the original design dead?

The direct drive one? The discussions here and most attempts I could find are dated around 2010. There are probably reasons behind this, but I couldn't find any clearly stated, so I can only guess -...

View Article

Re: Rostock Stepper Motor Problem - Help

All 3 jumpers are installed under all the drivers.

View Article


Re: Rostock Stepper Motor Problem - Help

did you check if all jumper has metal inside? sometime they come without (faulty) i am not an expert but if you are sure its board problem and you can not ask for replacement then i think it is...

View Article

Re: Rostock Printer build

Ended up buying the mechanical ones, Simply because they come with wires, cutting down on the soldering. Speaking of which I need to source some connectors for my motors. Probably scrounge up some or...

View Article


Re: Kossel endstops

I finally figured it out after much searching and mulling it over. The other 3 end stops are intended to help align the linear rail which I'm not using not to be min positiion switches. Min position...

View Article

Re: Automatic Tool Changer

Santa brought me something today! Arranged based on the principle I mentioned earlier. Pairs of disc magnets oriented in the same direction to create an open circuit that the ball bearing closes. As...

View Article

Re: Automatic Tool Changer

Neat! Never tried arranging magnets, pins, and bearings like that before. It certainly feels different from when I tried just pins and magnetic ball bearings, but still a lot weaker than my current...

View Article
Browsing all 20291 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>