Re: Mini Kossel bed leveling
The old forum thread does not have the picture any more so I cannot interpret what is wrong. But it does not matter. I can give you few ideas. There are 2 kinds of auto-leveling: * the original grid...
View ArticleRe: Mini Kossel bed leveling
I've looked at that wxm file at least a dozen times, didn't start making sense until I got this far into calibration. Thanks for the reminder it was there :). I still have a question on it though...
View ArticleRe: interest in pellet Bowden extruder for deltas?
Why not just extrude into a cooling section, then straight into the bowden tube. I think you are going to run into problem when you retract. The filament will have no where to go like it does when it...
View ArticleRe: Can't Disable Auto Bed Leveling
In your Marlin_main.cpp look for this line, I found mine around line number 3294. Quotevoid adjust_delta(float cartesian[3]) Add this line to the line above the one you just searched for. #ifdef...
View ArticleRe: interest in pellet Bowden extruder for deltas?
Could you elaborate on a cooling section? On the first idea, yes, there would be difficulty upon retraction. However, Im looking into the similar methods from magnetic tapes, which allows one to...
View ArticleRe: Mini Kossel bed leveling
You are right meaning for your radial/diagonal movement is just the opposite of the radial/diagonal in the maxima notebook.
View ArticleRe: Can't Disable Auto Bed Leveling
Thanks for the reply, it fixed the compiling error! Another problem i have been having is with my end stop switches. When I plug my end stops into the y-max, x-max, and z-max pins they don't trigger....
View ArticleRe: Help with Kossel Auto Bed Leveling...
Hi, i developed a kossel mini printer and follow the assembly guide with all care, i finish the assembly and now i´m trying to do the callibration of the printer using the printer bed auto levelling...
View ArticleRe: Can't Disable Auto Bed Leveling
In your config I see your X and Y homing direction are set to 1, change this to -1 so that X and Y are both at 0 (centered) when the machine is homed. Move the carriages away from your endstops and...
View ArticleRe: Mini Kossel bed leveling
Thanks for the help hercek. I've just about got it dialed in, probably a few more hours of tweaking the tower positions. Would you consider this forum post as good a spot as any to post my final steps...
View ArticleRe: Can't Disable Auto Bed Leveling
My endstops are wired for normally closed. When I send M119 without any of the switches touched I get >>> M119 SENDING:M119 Reporting endstop status x_max: open y_max: open z_max: open And...
View ArticleRe: Heated Build Chamber for Kossel
I'm totally new to this but what I thought was that the heat from the heated bed is mostly important to avoid warping for the first layers, and not so important for the top layers. Also the heat might...
View ArticleRe: Idea: A RepRap Hanging From the Ceiling
Sorry for disappearing like this. Yes, samp20, that sounds like a good compromise. I'm very eager to test this out in real life now. I have been using alot og time trying to find someone to cooperate...
View ArticleRe: Idea: A RepRap Hanging From the Ceiling
Just a few ideas: Maybe this SkyDelta design could actually be used for 6 degree of freedom? Or rather 5 degrees of freedom. Anyway similar to the sextupteron. So instead of designing ways to keep the...
View ArticleRe: Sextupteron
I love this design! Wouldn't something like the Beaglebone Black with an advanced BeBoPr++ or CRAMPS be a better controller for an advanced design like this?
View ArticleDelta Rostock level calibration problem
Hi Guys I have been tearing my hair out for the last couple of weeks. I have searched the web high and low, but cant find the answer. I have calibrated my delta as per this recommended site...
View ArticleRe: Help with Kossel Auto Bed Leveling...
That seemes to be exactly the problem I also have, did you change something on the original geometry?
View Article