Re: Cherry Pi III Is Available
Thanks, Andy. I'll just use the stl file for ideas on how to best modify the 3DR simple effector. I'm using solidworks so sketchup files won't do me much good. I can appreciate not wanting all of your...
View ArticleRe: Full Graphic Smart Controller Issue
Quotechamarejc Then I tried without the graphic controller and miracle, all works fine. Am I alone to meet that problem ? ( Marlin 1.03) There have been at least a dozen posts here in the past 60 days...
View ArticleRe: Calibrating Geared Extruder
OK so the fix I found was.....to just pull the 3 jumpers out from under the driver. 10mm now extrudes a bit over 10mm. Done.
View ArticleNew build problems
Hello, I just finished building a Rostock. I seem to be having some issues with my electronics/firmware. I am using the richrap firmware (linked here: [github.com]). Is this a good firmware to use? I...
View ArticleRe: Full Graphic Smart Controller Issue
On one of my machines I went from Marlin to Repetier and reduced the micro stepping from 1/32 to 1/16 on the DRV8825 drivers. The machine was fine with the full graphics lcd after that. I printed at...
View ArticleRe: Calibrating Geared Extruder
Quotefrankenfrankenstuff OK so the fix I found was.....to just pull the 3 jumpers out from under the driver. 10mm now extrudes a bit over 10mm. Done. Or you could put the three jumpers back and,...
View ArticleRe: Struggle with endstops
hhmm, I assumed you were using Marlin. I don't know what setting to change in Repetier to invert the end-stop logic from NC to NO. Have you checked that your X-tower motor is plugged into the...
View ArticleRe: 3DR "Simple" Delta Printer
John, Can you post your updated Solidworks files to github? the SW files on your git are all old.
View ArticleRe: 3DR "Simple" Delta Printer
Has anyone made a center section for top and bottom to make ths thing bigger? Flat ends and about 4 inches in length. Earl
View ArticleRe: 3DR "Simple" Delta Printer
thanks, I'm not good at cad 6 all the same for 3 on top and 3 on bottom. Should make print area bigger. Earl
View ArticleRe: GUS Simpson
Every day I'm shufflin' [attachment 35180 GUS01aFirstAssembly.jpg] The base is just a hand cut job. I'm hoping to get a CNC cut MDF base made any day now. Anyone know where I can order a basalt base...
View ArticleRe: GUS Simpson
I would like to see some one test a ceramic pizza stone for a build plate, they're not nearly as thick as the basalt, and they're a bit pricey for a new large one, but I've seen thrift stores carry them.
View ArticleRe: Cherry Pi III Is Available
@umdpru - Actually, I posted an answer before but it seems that it did not post. Thank you for advice. I tried in the past to do it through SW as you mentioned in your post but I got a lot of facets...
View ArticleRe: Rostock mini pro, problem with movements
yes i had shorted something..., that was my fault, but i got a new RAMPS, now the same issue as before. EDIT: I found the problem and solved it! yyou were right i just used the wrong pins, now it all...
View ArticleRe: Rostock mini pro, problem with movements
It depends .... As with all things Marlin lol. If you have configured your RAMPS in Configuration.h as 33 this tells Marlin that you, potentially, want a hot end heater, heated bed and one fan. If you...
View ArticleRe: Cherry Pi III Is Available
@zoltan: Hope I wont sound rude cause It's not what I mean. What your asking as notthing to do with 3D Printer, but rather 3D Design. There's a lot of tutorial on the web for SketchUp or other...
View ArticleRe: Rostock mini pro, problem with movements
As AndyCart said, the default fan(D9) is connected just bellow HotEnd Power(D10), see attached image. I also have Rostock Mini Pro by 3dPrinterCzar and spent first month calibrating and tweaking so...
View ArticleCore XY Printer £100.00 Build Cost
Hi Guys I know it's not a delta but I thought you may be interested in my latest design. It's a core XY machine that uses Igus bearings and cheap rods. The drive system uses spectra line and printed...
View Article