Re: Rostock mini pro, problem with movements
QuoteDinoK As AndyCart said, the default fan(D9) is connected just bellow HotEnd Power(D10), see attached image. I also have Rostock Mini Pro by 3dPrinterCzar and spent first month calibrating and...
View ArticlePerfect Build Surface For PLA?
Hi Guys I thought I would share a discovery with you that I haven't seen documented elsewhere. I am a big fan of PLA but, as we all know, it's a bit of an effort to get it to stick well to the bed...
View ArticleRe: Rostock mini pro, problem with movements
You can disassemble it but only when it's hot so be careful. I've had some luck by taking the bowden tube out at the effector end and pushing the blunt end of a 2mm drill bit down the PTFE in the J...
View ArticleRe: Cherry Pi III Is Available
@ nka - Thank you for advice. Actually, you are not rude or at least I do not consider this but it seems that you did not read the whole discussion. I have asked Andy if he has igs or step files of...
View ArticleRe: Cherry Pi III Is Available
On my bad... searched a bit, could not find anything also. I don't know much about SW, but I know it's pretty good designing thing that need measurement, assembly or mechanical parts :)
View ArticleClik here to view.
Re: Rostock mini pro, problem with movements
I had to disassemble the hotend also at the begining since they are cheap clones of J-head MK-IV and also poorly assembled. More about the clones : Quote... has 4 cooling vents, a push-to-fit...
View ArticleRe: Core XY Printer £100.00 Build Cost
Looks good! Got a link to the supplier of the squirrel cage fan.
View ArticleRe: Struggle with endstops
Hi Umdpru, GREAT! Thanx! That worked! (tu) Now it homes perfectly, the only issue now is that it can't move after it's been homed. The z-value gets red on repetier (after a g28) and show Z top value...
View ArticleRe: GUS Simpson
Quote I don't know how well a ceramic tile will function as a heated bed. I'm guessing quite spectacularly badly Actually, it is probably one of the best beds to use. As a great discussion on another...
View ArticleRe: Rostock mini pro, problem with movements
I've used a few clone j heads in the past and as long as you set them up right they are o.k. The main issue with the ones I have tried is that they don't have the lock nut holding the PTFE liner tight...
View ArticleRe: Perfect Build Surface For PLA?
Plastic type materials do tend to not steal as much heat as glass does. Touching glass and plastic at the same temp, the glass usually feels colder. In my mind, this works like the surface heating...
View ArticleRe: Cherry Pi III Is Available
I've pulled the trigger and begun amassing parts to build one of these bad boys. Andy, I'm really excited about what you've done here! And, like you zoltan, I've got the hair-brained plan of using...
View ArticleRe: Perfect Build Surface For PLA?
There is a guy who goes to events at my hacker space who used acrylic all the time. The problem is, it can sometimes stick too well, and then there's the times where the head hits and digs a track...
View ArticleRe: Cherry Pi III Is Available
Hi Maso In regard to enlarging the hole in the top vertex to take an M8 bolt for your 608 bearing you may run into an issue. My design uses an M5 bolt through the hole and into a T nut in the tower to...
View ArticleRe: Cherry Pi III Is Available
QuoteAndyCart My design uses an M5 bolt through the hole and into a T nut in the tower to fix the top vertex to the tower. Interesting. That's not evident looking at the STLs; there's a wall at the...
View ArticleRe: LISA Simpson
I've found some rather cheap ball screws on ebay 800mm and 1610 (apparently 10 mm lead), in the range of $60 with free shipping. These have less lead than the high lead screws, but they also have far...
View ArticleRe: Cherry Pi III Is Available
All, with regards to modifying Andy's design - I would get permission from him. Also, I believe it's a part of the licensing to make modified files available under the same licenses? I don't know much...
View ArticleRe: Cherry Pi III Is Available
Hi Maso I'm away on vacation for a couple of weeks so can't upload any images. But you are correct. The two flanged bearings have their non flanged faces together to form a channel for the belt. I've...
View ArticleRe: Perfect Build Surface For PLA?
Quotesheepdog43 There is a guy who goes to events at my hacker space who used acrylic all the time. The problem is, it can sometimes stick too well, and then there's the times where the head hits and...
View ArticleRe: LISA Simpson
So $180 for a set of 3. I think these would be perfect. They should be super straight and there should be no backlash. I think you would be happy with the speed reduction. I never really hit the...
View Article