Calculating rods length and radius for X Y and Z towers
Hi, Where can i find information about where to place X, Y and Z towers like the radius and the length of the rods ? donnib
View ArticleRe: Cherry Pi III Is Available
If I understand right, rods and ball need to be the same size, but the wire / spring can vary, as long as it's tight enought to hold everything in place? If yes, it's less complicated that I was...
View ArticleRe: Cherry Pi III Is Available
btw, when my printer will be done, I'll be trying to use a 110V heatbed with an SSR from Keenovo ( [www.keenovo.com] ). 40$ for 300W 200mm dia, 3M stick PSA on glass, NTC Thermistor (custom order)....
View ArticleRe: Calculating rods length and radius for X Y and Z towers
This is what I used for my printer. You don't have to be 100% acurate on the rod lengths, however you do have to be very accurate to match the rods to each other as close as possible. I have roughly...
View ArticleRe: Mini Kossel Z Calibration Issue
Someone mentioned some errors with delta calculations with 20 tooth pulleys on marling firmware. I have the 20 tooth pulleys on my printer, so far no issues. Keep in mind two things however, 1 plastic...
View ArticleRe: Curious delta problem: slanted prints
I just took a look at the pic. Your not cooling the hot end at all it looks like. I don't either. However I can say that from the pic it looks like the hot end is slanted. I bet your getting...
View ArticleRe: Which Firmware (and Version) Do You Use For Your Delta and Why?
Interested by this. *Subscribing*
View ArticleRe: Mini Kossel Z Calibration Issue
I verier the pulleys and they are proper 16. I think i'm going to start calibration all over again and see if I missed something. I will give cura a try also. I have been using slicer. Thanks for the...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
What size braided wire sleeving did you use? I need to order some. Thanks. Looks really good.
View ArticleRe: Which Firmware (and Version) Do You Use For Your Delta and Why?
...Which Firmware are you using? Upgraded Repetier Version 0.83 to 0.91.7 ... Why are you using this particular version: My printer came with an older version and upgrade was easy. Printing is great....
View ArticleRe: Cherry Pi III Is Available
The new string-spring plan looks like a good one! Is the change due to some problem with the magnet plan, or is it more to simplify the design? I haven't quite finished my printer yet, so haven't had...
View ArticleRe: Cherry Pi III Is Available
A thought that occurred to me while I was building my printer was that if the pivot-points for the arms (was magnets, now balls) were located higher up on those carriages, it'd be possible to get some...
View ArticleExtruder options.
Well I have just recently reprinted airtrippers bowden extruder as the pla version deformed badly. I notice that even the abs part has some flex in it, it flexes a bit when it retracts and pushes, I...
View ArticleRe: Cherry Pi III Is Available
Quotedisneytoy What size braided wire sleeving did you use? I need to order some. Thanks. Looks really good. I used this [www.amazon.co.uk]
View ArticleRe: Extruder options.
I've always used the Greg's Wade version with herringbone gears that Richrap designed for the 3DR. It just works!
View ArticleRe: Extruder options.
I have an MTW Maxstruder. The metal it is constructed from will stop small caliber arms fire. :) It isn't cheap, but the design is simple enough where you can probably make a knockoff in your garage...
View ArticleRe: Which Firmware (and Version) Do You Use For Your Delta and Why?
I think there are really two Marlin forks that you should be concerned about: Johann's original firmware and Rich Cattel's firmware. There are two versions of the Johann's firmware. There is the...
View ArticleClik here to view.
Re: Extruder options.
This interesting extruder just popped up on Thingiverse yesterday: http://www.thingiverse.com/thing:409594 Image02_preview_featured.jpg It looks beefy enough where I wouldn't be worried about flex,...
View Article