Re: Cherry Pi III Is Available
Quotenka I tried the "G30 A" on a 40mm bed (more than that, rods are disconnecting) until I get the new part. I runned for 17 time until I stopped it. Does it run until all parameter are staying the...
View ArticleRe: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text
Keep us posted with the accelerometer project. I saw your post on GG about it. Seems to offer all sorts of benefits. The impact sensing for Z probing looks very promising.
View ArticleRe: Core XY Printer £100.00 Build Cost
Quotereprapturk If there is no such case, where can I get Z lead screw nut you use for PrntQB V2? Sorry I missed that one! I made the lead screw nut from a piece of UHMW polythene (an old plastic...
View ArticleRe: Core XY Printer £100.00 Build Cost
Quotevreihen QuoteAndyCart 1. Which controller board would you suggest? I am planning to get Azteeg X5, is this controller suitable to PrintQB? Any controller that supports Marlin with core xy...
View ArticleRe: Core XY Printer £100.00 Build Cost
Quotereprapturk So it means that I will be using 8 bit out of 32 bit controller, if I use Smoothieware with corexy. Right? Smoothieware is 32-bit, and runs on a 32-bit processor. Marlin is 8-bit, and...
View ArticleRe: Cherry Pi III Is Available
Oh so that's normal. I guess the software is trying to get the same result as the last test before calling it "Done". Can wait to try again with the new setup. It was doing 2 tap on the middle, and...
View ArticleRe: Cherry Pi III Is Available
i had the problem with much tapping too. in my case i set m y x y z steps per mm from 80 to 80.2 after that the auto leveling was tapping 10-15 times till the piont was stored. with 80steps/mm the...
View ArticleClik here to view.
Arm length calculation help on own-design delta needed
Hi All, I'm building a delta and I've got to the stage where I need to cut the arms to length. On my design, the distance between towers is 268mm and the rule of thumb seems to be 80% of that...
View ArticleRe: Cherry Pi III Is Available
hello Andy, Realy love your job on this printer! I'm currently working on making one but i'm not gonna use magnetic arm , i have some traxxas Rod end and some carbon tube to make my arm. My problem is...
View ArticleRe: Extruder options.
QuoteKurzaa I definitely like the idea of a quick release, not that I really have a reason to swap filaments...only have the one roll. Though I wonder if heating up my hot end would help with loading...
View ArticleRe: Arm length calculation help on own-design delta needed
The image is missing delta effector offset and delta carriage offset. But do not bother. Make them long enough so that the hotend can reach the far edge just opposite a tower.
View ArticleRe: Cherry Pi III Is Available
Last night, I had *another* spherical magnet break free of the CA glue on my effector plate mid-print! :( My printer uses 1/2 inch (12.7mm) spherical magnets, and I used my ball end mill to ream the...
View ArticleRe: Curious delta problem: slanted prints
Quotejaguarking11 I just took a look at the pic. Your not cooling the hot end at all it looks like. I don't either. However I can say that from the pic it looks like the hot end is slanted. I bet your...
View ArticleRe: Cherry Pi III Is Available
you should look some post above, there's a new solution without magnet. In fact, this post : [forums.reprap.org]
View ArticleRe: Arm length calculation help on own-design delta needed
I really like the idea of just making the arms long enough to ensure coverage, that makes a lot of sense to me! Thanks for taking the time to look. Barny
View ArticleRe: Arm length calculation help on own-design delta needed
Really you do not want it much longer since it lowers your maximum print height and makes it harder to detect calibration errors. You do not want it shorter since you would not be able to reach to the...
View ArticleRe: Cherry Pi III Is Available
QuoteCammi hello Andy, Realy love your job on this printer! I'm currently working on making one but i'm not gonna use magnetic arm , i have some traxxas Rod end and some carbon tube to make my arm. My...
View ArticleEffector "Rocking"
Hey guys - Im having a slight issue on my Delta. The Effector "rocks" ever so slightly when its moving. its easier to see on the infill movements as it moves back and fourth quickly. As a better...
View ArticleRe: Arm length calculation help on own-design delta needed
I've always used the 80% rule of thumb. One point to note is it's 80% of the distance between tower centres not just between the towers as in your diagram. That additional 20mm probably wouldn't...
View ArticleRe: Effector "Rocking"
That rocking normally occurs when there is play in the tower carriages. If you get hold of one can you turn the face clockwise and anti-clockwise? You need to ensure the tops of the carriages are...
View Article