Re: Cherry Pi III Is Available
Andy, can you give a link to where you found the 8mm ball bearings with the 4mm hole? I'm having no luck finding them.
View ArticleClik here to view.
Re: Cherry Pi III Is Available
As for the spring loaded idle, I was thinking of something like this wtGm60u.jpg (M8 is too big... M5 or even M3 should be okay). Installed like this dSWdF5g.jpg Two part would be fixed to the top...
View ArticleRe: Marlin v1 issues MANUAL_Z_HOME_POS
I'm running MLX 6mm belt width 18 teeth. I'm running 1/32nd steps. my mistake, although I did change it in the EEPROM I never changed it in the firmware .This is what it looks like now (#define...
View ArticleRe: Rostock calibration
Look at this thread. It seems like a similar issue to you. Give the fix a try and see if that fixes the problem. [groups.google.com]
View ArticleRe: Core XY Printer £100.00 Build Cost
Quotejregholdsworth Interested but can't find where to source the igus bearings? can you give me any pointers? Www.igus.com
View ArticleRe: Core XY Printer £100.00 Build Cost
Feeling quite dull.,...you might live in the last of the summer wine territory but I is one...thanks anyway
View ArticleRe: Cherry Pi III Is Available
I don't know how it would be applied to the Mini Kossel / Cherry Pi design (well, I do-- redesign the top bracket from scratch), but the belt tension mechanism on the Kossel Clear is nice-- the idler...
View ArticleRe: Marlin v1 issues MANUAL_Z_HOME_POS
I solved the problem by typing in M 666 L this is the result you get 07:17:19.871 : N22 M666 L *89 07:17:19.876 : Current Delta geometry values: 07:17:19.876 : X (Endstop Adj): 0.00 07:17:19.876 : Y...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
Just a little improvement I would do on the Effector Clamp Moving the nuts hole a little would help to reach the nuts and then tight without going into the wall of the other screw (in case of a...
View ArticleRe: Marlin v1 issues MANUAL_Z_HOME_POS
Eprom is all fine and good, but its no replacement to modifying the firmware properly for your build. I turned eprom off on my printer, as well as auto leveling is off. Its the harder way to tune a...
View ArticleRe: Effector "Rocking"
Nope, Sockets are good - there is nothing loose at all. I reprinted a new effector as My carriages were found to be a bit wider - but that didnt change anything. Ive checked and checked all my...
View ArticleRe: Cherry Pi III Is Available
I second Sebastien's suggestion! My added rationale is that my bag of assorted Mini-Kossel M3 SHCS hardware only had two screw lengths in this range. One just reached the face of the nut when pushed...
View ArticleRe: Effector "Rocking"
What about slop? What if the problem that you are seeing is similar to the traxxas joints where the effector will still have small movement on the joints. Magnetic joints seem to suffer from the same...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
If you are considering a re-design of the bottom brackets, may I suggest cherry-picking this concept? http://www.thingiverse.com/thing:340529 frame_motor_2020_QD_ASS_preview_featured.jpg Instead of...
View ArticleFederate issue Rostock Mini with Marlin
Hello, I just finished to build my Rostock mini and everything seems to work fine exept the federate speed that seems much faster then what setup in Cura or Slic3r. Even if I set something like 10mm/s...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
Quotenka Just a little improvement I would do on the Effector Clamp Moving the nuts hole a little would help to reach the nuts and then tight without going into the wall of the other screw (in case of...
View ArticleRe: Cherry Pi III Is Available
yeah, its not a "problem", just give more room to play :)
View Article