Re: Kossel Repetier FW Z-Tower not moving down
Quote#define MAX_FEEDRATE_X 200 #define MAX_FEEDRATE_Y 200 #define MAX_FEEDRATE_Z 2 .... 2? Seems a bit... small.
View ArticleRe: Reprap Rostock with Repetier Firmware - what relative position is the...
Ahh Cheers Andy, It works!
View ArticleWant to do a "pencil" dry print, but will not do x and y movements after the...
Hello all, I've got a Rostock printer built up and connected except for the Extruder motor, Extruder hot-end and the hot bed. I want to do a calibration "dry-print" where I attach a pencil to the...
View ArticleWhat Delta Variation?
Hi, first time posting but I have been following this forum for a long time. I am thinking of building my 4th printer and I want it to be a delta bot. I am stuck between 2 models I like the Rostock...
View ArticleRe: What Delta Variation?
I was considering the same and ended up building a Kossel mini with 2020 extrusions, 360mm horizontal, 900mm vertical and 330mm diagonal arms. That gives me a printable range of ~280x450mm. I'm very...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
Oh, here is the screenshot of the Prointerface: [www.dropbox.com] As you can see, it stalls at 0.01% of the print, and a status message of T:15.7, E:0, W:? (no idea what is W). I also have a z_min...
View ArticleRe: Kossel Repetier FW Z-Tower not moving down
Changed the max z feedrate but it didn't change anything.
View ArticleRe: Cherry Pi III Is Available
Has everyone just been directly wiring in a mains cord to their PSU, that basically goes from the PSU straight to the wall? Has anyone played with the idea of throwing a fused IEC plug into the mix? I...
View ArticleRe: Kossel Repetier FW Z-Tower not moving down
Seemed to be a endstop problem with the z min endstop. Now my question is do i disable this z min endstop completely and what will be the effect on the z-probe/auto-level when i do this? Will it still...
View ArticleRe: Cherry Pi III Is Available
I'm running an ATX power supply externally for the moment, but did pick up one of these for when I go 24V in the future:...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
Hi DennyP! The W seems to be a countdown that tells you it is almost starting, it waits until the temperature has been reached for a few seconds. My Pronterface shows: T:200.2 E:0 W:8 T:200.6 E:0 W:7...
View ArticleDoes inverting x and y influence calibration ?
Today, I calibrated my new Rostock Delta Mini Pro. But I forgot to invert x and y, so currently, the Z=ok and x/y are reversed. But calibration of the bed is fine. What wil happen when I change the...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
Maybe have a look at Repetier Host as well ? It will simulate the circular print bed in its guy ánd it will allow dry run by hitting the cold button. I was a pronterface fan first, but are getting...
View ArticleRe: What Delta Variation?
Whatever you do, don't use 15x15 extrusion, it's far too small for scaling to the size you want and you will end up with a wet noodle for a frame. There are some upscaled Kossel parts out there as...
View ArticleRe: What Delta Variation?
Thank you so much for all the information guys, I was actually thinking on using 15x15 however I did notice that the seemecnc uses 1" extrusions, and now sheepdog43 just confirmed what I was thinking,...
View ArticleRepetier Firmware 0.91 Feedrate 2??
Hi, When configuring my kossel i set the feedrates to 200. But after uploading and restarting the controller it displays feedrate 2 (Controller Menu: Configuration/Feedrate)? #define MAX_FEEDRATE_X...
View ArticleRe: Repetier Firmware 0.91 Feedrate 2??
Repetier takes configuration data from EEPROM (instead of Configuration.h) if both of these are valid: 1) EEPROM is enabled 2) EEPROM_MODE is not different from the value it had during previous...
View ArticleRe: Kossel Repetier FW Z-Tower not moving down
x/y/z min endstops are independent from z-probe micro-switch in Repetier. Disable x/y/z min endstops in configuration. Set z-probe pin to one of (now free) x/y/z min endstop pins. E.g. I set it to 3...
View ArticleRe: Cherry Pi III Is Available
Nice! Yeah, that's what I was thinking too vreihen. [www.jaycar.com.au] Think I might build it with a hard-wired mains cord to begin with, but once I can print out some parts, I'll make a nice little...
View ArticleRe: Cherry Pi III Is Available
If you cut it too long, it's not that bad, you can just lower the top braquet (without the top).
View Article