Re: What Delta Variation?
Don't use an extruder based on the pretty pictures, or even how many extruders they have designed. Not only could you could say they just haven't yet figured out how to do it right, but you also don't...
View ArticleRe: Cherry Pi III Is Available
Quotepugzor Nice! Yeah, that's what I was thinking too vreihen. [www.jaycar.com.au] Think I might build it with a hard-wired mains cord to begin with, but once I can print out some parts, I'll make a...
View ArticleRe: Cherry Pi III Is Available
Well the GT2 belt is only used for the 3 vertical movements, right? I think it's going to be REAL close on whether I can do this or not with my existing GT2 belt... I think it mostly depends on...
View ArticleClik here to view.
What parts do I need to replace / modify if i use 2020 aluminum frame for...
Hi, I decided to build Kossel Mini from scratch as my first Reprap 3D Printer. Misumi HFS3-1515 has 3.4 mm of slot size where the wheels of motor mounting plate seats. The 2020 aluminum extrusion I...
View ArticleRe: Repetier Firmware 0.91 Feedrate 2??
Thanks Hercek, That was indeed the issue. What is the difference between enabling and disabling the eeprom? And how can i set the correct eeprom value?
View ArticleRe: Repetier Firmware 0.91 Feedrate 2??
When EEPROM is enabled (EEPROM_MODE > 0) the configuration data are taken from it. You can reload EEPROM with data from Configuration.h with M502. You can edit EEPROM with repetierHost in a grid...
View ArticleRe: Cherry Pi III Is Available
Quotepugzor I think it's going to be REAL close on whether I can do this or not with my existing GT2 belt... I think it mostly depends on whether or not I have exactly 4 metres. I managed to use some...
View ArticleRe: Cherry Pi III Is Available
QuotepugzorA quick question and it's not terribly related to the Cherry Pi, but one of my pulleys from OpenBuilds is slightly damaged. 2 of the teeth have chunks missing on them (I'd say it reduces...
View ArticleHow to invert x and y, but not z
After finishing my Rostock Delta Mini Pro, I notice that the X and Y movements are inverted as to the grid arrows in the Repetier Host control panel. I tried to set invert_x_dir and invert_y_dir to...
View ArticleRe: How to invert x and y, but not z
Inverting the steppers won't solve the problem, as you have already found out. It just changes up to down or vice versa on the towers. I suspect you have X Y & Z on the wrong motors. Looking from...
View ArticleRe: What Delta Variation?
Thank you Sheepdog43, I'll stick to 1.75mm for my Delta, I agree with you 100% geared extruders are the way to go much more reliable than direct, I have tried many extruders they always seem to work...
View ArticleRe: Cherry Pi III Is Available
Got my parts from Andy today! *dances* It sure is a bright yellow Andy haha. Should be good though. Everything arrived intact other than the feet on one of the tower bases. Are they needed or can they...
View ArticleRe: What parts do I need to replace / modify if i use 2020 aluminum frame for...
20x20 V-slot is even cheaper at $10 per 1meter length and Ultibots sells pre-cut lengths for the Kossel Mini at about $60. You don't even have to modify anything, they even provide the necessary STL...
View ArticleRe: What Delta Variation?
Oops, I meant nothing was as easy as a geared stepper motor. All the power of a geared extruder, with the simplicity of direct drive. Geared extruders look great, and on a cartesian are fine, on a...
View ArticleRe: What Delta Variation?
I am with you on geared extruders beaing big and they do look clumsy, that is why I liked the Infill3D geared extruder the gears are small is hard to see it in the pictures but once you hold it in...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
Thank you for the responses. I've since updated my marlin and now my configuration file is represented as this dropbox link: [www.dropbox.com] To 3D-ES, Thx for your reply! It makes sense what you say...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
You can tell Pronterface to show more GCODE output, there is a "Debug G-code" option in the settings menu. It looks like the printer wants to print, but waits for something. Do you have a M109, M116...
View ArticleRe: Cherry Pi III Is Available
Hi Andrew Glad it arrived safe. Yes it is YELLOW isn't it. Unfortunately I'm always in the hands of the supplier and the images on their website. I've never had that colour before so it was a bit pot...
View ArticleMarlin Delta Firmware Issue
Hey, I keep on getting this error with ErikZalm's version of Marlin. when I try and verify the code I get this error: redefinition of 'float delta [3]' Marlin_main.cpp:321: error: redefinition of...
View Article