Re: Cherry Pi III Is Available
QuotenkaAndy (or someone else), I'll have to reprint the wheels carriage to match my spring loaded carriage. I have MISUMI extrusion, what version should I use?...
View ArticleWhy G codes?
I only recently built a Kossel mini for a friend but am planning a Delta machine for myself. Perhaps this is a noobish question to which the answer should be obvious but it has me perplexed. It makes...
View ArticleRe: Why G codes?
Could the splines be created in some sort of gcode so that the amount of data in the gcode file and the work done by the Arduino are both optimized? But then 32 bit Arduinos for $20 are not far away...
View ArticleRe: Magnetic Joints
Hercek, thank you for the link you made up my mind is too much trouble doing the traxxas I am going the magnetic route.
View ArticleRe: Arm length calculation help on own-design delta needed
What angle should the rods have when the nozzle is all the way to the edge of the printing bed? Is it 20 degrees?
View ArticleRe: Arm length calculation help on own-design delta needed
Based on my reading of the advice i got on this theread, i wound up using a measurement which would allow the effector to reach the far side of the bed, plus a little bit. It's not very scientific,...
View ArticleRe: Arm length calculation help on own-design delta needed
Thank you ybanrab, perhaps this picture can illustrate it better, I follow some of the posts to calculate different lengths of the rods in the picture you can see them as pairs of what angle they...
View ArticleRe: Magnetic Joints
Good ball joints are much better (no play, light, strong) than magnetic. The problem is traxxas is not good if not carefully assembled. If you can then get e.g. MP-Jet ball joints.
View ArticleRe: Magnetic Joints
Thank you Hercek, that is another option I appreciate it. In another post I saw something similar but they where all aluminum I do not remember what post was it. I been following another thread where...
View ArticleRe: Cherry Pi III Is Available
Oh... this is sad... even more when I think that I got ripped of with shipping they don't tell you until they ship!
View ArticleRe: Magnetic Joints
Quoteplastik Hercek, thank you for the link you made up my mind is too much trouble doing the traxxas I am going the magnetic route. If only that statement were true. My advice, don't drink the Kool...
View ArticleRe: Arm length calculation help on own-design delta needed
Using 60 degrees is absolutely pointless. Tell me ANY time where that measurement actually matters to the printer. The only time it hits 60 degrees is at top, in the resting position. It has no...
View ArticleRe: Arm length calculation help on own-design delta needed
Quotehercek Quotesheepdog43 Also, if you plan to auto level or auto calibrate, just reaching the edge of the build plate is not enough. The further out you go, the more flat one arm will be, leaving...
View ArticleRe: Rods angle
Ignore the resting angle, it's irrelevant. See the other thread for more. [forums.reprap.org]
View ArticleRe: Delta without parallelogram?
QuoteFede3D So I guess to start with a conventional delta, and once I can print my custom parts in 3d, I can begin to experience something new without wasting too much money. It's handy having a...
View ArticleHelp with configuring FSR probe points (mini kossel with RUMBA)
Hi everyone, I am hoping someone can help me figure out why my mini kossel is not cooperating with my FSR's. This is my first delta build, so forgive me if I'm totally clueless. I've got it built,...
View ArticleRe: Magnetic Joints
All good points sheepdog43, thank you. Now I am back to the MP-Jet ball joints, can someone please point me to the all aluminum ball joints? I know they are out there but I can't find the darn thread...
View ArticleRe: Arm length calculation help on own-design delta needed
Thank you sheepdog43, cyan it is! :)
View Article