Delta Printer setup help :S
Hi I have been trying to get my Reprap Rostock printer going and I ran into an issue and I was wondering what I need to do to fix it. When I use the commands to move the printer in the horizontal...
View ArticleRe: Cherry Pi III Is Available
Could you add a 45 degree chamfer on the slots with a square file?
View ArticleRe: What parts do I need to replace / modify if i use 2020 aluminum frame for...
There is a complete 20 mm and 25 mm Mini Kossel STL right here: http://www.thingiverse.com/thing:154832/#files
View ArticleRe: Help with configuring FSR probe points (mini kossel with RUMBA)
You need to set X Min and Y Min pins to -1 in Pins.h
View ArticleRe: Magnetic Joints
Another alternative is to use the system I use on my Cherry Pi IIIS models. It has all the benefits of magnetic attachment, precision, ease of removing the effector, etc but none of the draw backs....
View ArticleRe: Arm length calculation help on own-design delta needed
Quoteplastik What angle should the rods have when the nozzle is all the way to the edge of the printing bed? Is it 20 degrees? The angles change with changing printer delta radius and diagonal rod...
View ArticleRe: Delta Printer setup help :S
Hi Tanner Your steps per mm is correct. I suspect you don't have the jumpers under the drivers set correctly. You need all three on there for 1/16 microstepping (unless you are using DRV8825 drivers...
View ArticleRe: Cherry Pi III Is Available
QuoteAndyCart Could you add a 45 degree chamfer on the slots with a square file? http://3d.grabercars.com/?product=dual-623-wide-v-roller-fits-both-3mm-and-8mm-t-slot-extrusions I was thinking that...
View ArticleRe: Arm length calculation help on own-design delta needed
Quotesheepdog43 Quotehercek Quotesheepdog43 Also, if you plan to auto level or auto calibrate, just reaching the edge of the build plate is not enough. The further out you go, the more flat one arm...
View ArticleRe: Help with configuring FSR probe points (mini kossel with RUMBA)
Done, I think. There are many tabs in the top of the Arduino software and for some reason the scroll bar does not show up, so I can't click too far to the right of my screen to get to other tabs. So I...
View ArticleRe: Delta without parallelogram?
Your first printer ? Hmmmm. I have built 2 now. A full cartesian Orca v04x and A delta Mini I bought the Delta for fun, while the Orca suffered from a blown electronic part, but it is not fun. It...
View ArticleRe: Delta without parallelogram?
QuoteReplace I bought the Delta for fun, while the Orca suffered from a blown electronic part, but it is not fun. It looks amazing (one reason to build it ) but quality stays behind the cartesian. Of...
View ArticleRe: Delta Printer setup help :S
Ok I am not sure how to setup the jumpers, do you have a little bit more information about what I have to do? Do I just have to put jumpers on the three sets of pins on the RAMPS under the stepper...
View ArticleRe: Delta without parallelogram?
@ Replace I would start with a delta, because they are simple to design, 3 symmetries, once you've developed 1-axis ... you're done as regards the precision of the delta should theoretically be very...
View ArticleRe: Help with configuring FSR probe points (mini kossel with RUMBA)
Also, I'm getting nothing out of my hot end fan. When tested with a multimeter, there is not 12v across the Fan0 or Fan1 terminal, so I know the fan is not broken. I don't see where to change this in...
View ArticleRe: Delta Printer setup help :S
Quotetanner331 Ok I am not sure how to setup the jumpers, do you have a little bit more information about what I have to do? Do I just have to put jumpers on the three sets of pins on the RAMPS under...
View ArticleRe: Large Delta, small motors - Counterweights ?
QuoteXabbaxI have a delta with 3 extruders suspended from the top by 3 cables and counterweight system. A video at [plus.google.com]Wow, that thing is a monster! I remember seeing your thread with the...
View ArticleRe: Magnetic Joints
Hi AndyCart, thank you for the info, do you know if those ball bearings are still for sale in eBay? I am guessing that it would be a bitch to drill those out, not only because of the shape but ball...
View ArticleRe: Arm length calculation help on own-design delta needed
Thank you for the info Hercek.
View Article