Re: Lib for a Kossel Delta Printer
i dont know really whats Marlin or Repeater firmware. Im just studdyng computer ingenier, and i want to learn how to do that. Can u explain to me what should i do to control the delta Kossel? I...
View ArticleRe: Worm Drive Grounded Delta Printer
Looking good. What is the motivation to design an extruder? Will you be resin casting the extruder as well? I'm unsure, but it appears that you are using a fixed gap between the idler and hob. From...
View ArticleRe: Worm Drive Grounded Delta Printer
QuoteA2 Looking good. What is the motivation to design an extruder? Will you be resin casting the extruder as well? I'm unsure, but it appears that you are using a fixed gap between the idler and hob....
View ArticleRe: Lib for a Kossel Delta Printer
There is no reason to re-invent the wheel. Both the Marlin and Repetier firmware have already been developed to run a Delta printer, and both can be easily tailored to work on just about any...
View ArticleRe: Lib for a Kossel Delta Printer
I think i love u ^^. Really, thanks a lot. I was so lose. Now i gonna seek in this direction. Thanks. Really
View ArticleRound Heatbed D=400mm for Rostock, Kossel Delta
Hi, for your Information. I let develop and produce a round Heatbed for my new redesigned Delta (DeltaMax -> Buildarea D=400mm x/y and Z=850mm) Technical layout is finished now, PiBot designing it...
View ArticleKossel Mini Problem
Ok, so this apst week I decided that I would start building a Kossel Mini printer. I printed out all the parts on my Prusa Mendel and order the Open Beam and various nuts & bolts. Yesterday I...
View ArticleRe: Round Heatbed D=400mm for Rostock, Kossel Delta
Is this going to be a PCB board or one of the higher powered rubber or kapton based ones? I've been searching for ideas for a 250mm diamiter one for my delta. I looked at custom PCB costs and circular...
View ArticleRe: Fixed, non-mechanical probe idea: Inductive Proximity Sensors
I've used these type of sensors as end-stops in CNC machines. They can be triggered with aluminium but then it has to be pretty close. Iron or steel gets detected at 3 or 4mm if thick enough (an M8...
View ArticleRe: New Own Design Printer 'Cherry Pi'
Andy, I've been lucky enough to print out your design on my work's SLS printer. I've built up the frame and its starting to look good! I really like the design, it so simple and quick to put together....
View ArticleRe: Fixed, non-mechanical probe idea: Inductive Proximity Sensors
Hi Another thing to consider - they are temperature sensitive. Get them close to a heated bed and the sense distance will change. Bob
View ArticleRe: Round Heatbed D=400mm for Rostock, Kossel Delta
Rick, Here is an idea for you. At Lowes they have some relatively low density cement board called Hardie Board that is quite cheap and used as a backer for ceramic tile. Get a piece of that and some...
View ArticleClik here to view.
Re: Round Heatbed D=400mm for Rostock, Kossel Delta
What is the power draw on that behemoth? Can existing controller boards like RAMPS drive it without a relay and wiring it to wall (mains) power? I'm not sure why the BerryBot designer chose to use...
View ArticleRe: Round Heatbed D=400mm for Rostock, Kossel Delta
Hi RickM, Hi garyhlucas , Hi vreihen, thank you for your comments. I think it can be work for 12 Volt. It is logical, that I have to wait a little bit more longer to get the Temperature. Mainly I...
View ArticleRe: Kossel Mini Problem
maybe you can resolve this by loosening the bolts, correcting the stand and fastening them again. I had mine fixed in wrong positions first, too, but after some measuring (be sure to measure the...
View ArticleRe: Kossel Mini Problem
I tried loosening all the bolts and setting the whole thing on a flat surface while I tightened them back up right when I noticed the problem. It helped quite a bit (as it was very far off at first)...
View ArticleRe: Round Heatbed D=400mm for Rostock, Kossel Delta
Good luck with the heatbed - be sure to let us know how it goes, and if possible provide any info on a wiki page :) Also not sure if you'd seen this one or not but this is the SeeMeCNC Onyx heatbed....
View ArticleRe: 3DR "Simple" Delta Printer
JohnSL, I am attempting to follow your design and convert my Simple to a Delta. I have started printing parts with my Mini Kossel that I just finished building - I have the bottom wings printed,...
View ArticleClik here to view.
Re: LISA Simpson
Here is something I've been playing around with. The forked arms are contained with MR6702-ZZ (15 x 21 x 4 mm) Ball Bearing which will mate with a solid aluminum plug on either the shoulder or the hub...
View ArticleRe: LISA Simpson
That looks amazing! How do you insure no play when you don't have any fasteners? Do the cut outs actually save weight? They make it look cooler for sure. Do you have to print with support? What is the...
View Article