Re: Whats the latest and greatest Delta platform these days?
Quoteumdpru Sorry, Iceman086. Go to [groups.google.com] and check out the posts there. Not one for Griffin. That's not to say it's not a good printer. I'm just saying that the Mini Kossel is king of...
View ArticleProblem with Marlin
Hi everybody, I'm new in the world of the 3D printing , i've decided to build a Kossel mini. I sourced most of the parts from builda3Dprinter.eu and downloaded my first firmware from there. But now i...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
Woohoo... almost done. But I'm having two problemes; G30 work, but it "slam" into the bed... so much that a motor may skip steps, so when it begin calibration, he's not in the middle. Speaking of...
View ArticleRe: Perfect Build Surface For PLA?
This is what I am using. [www.amazon.com] It will only work with a heated bed.
View ArticleRe: Perfect Build Surface For PLA?
You don't add anything to it? What temps do you run at? Also, what do you secure it with?
View ArticleRe: Cherry Pi III Is Available
Hi Sebastien Looks great. If you are having arms disconnecting it may be that the delta rods are not exactly the same length. Check them. Another reason could be the bowden/cable loom is too tight and...
View ArticleRe: Problem with Marlin
Hi Canaylan It's probably because you have the EEPROM enabled. You can change DEFAULT_AXIS_STEPS_PER_UNIT and MANUAL_Z_HOME_POS without uploading Marlin using gcode commands. M92 Xnn.n Ynn.n Znn.n...
View ArticleHelp with Rostock parts
Hello RepRappers Around the beginning of the year, I started work on my first 3d printer, a Rostock, but put it on hold until now. I decided to start working on it again but still need a few more...
View ArticleRe: Problem with Marlin
It is working ! Thank you very much :) It is working. Do yo know where i can find a list with all the Gcode for this firmware ? Best regards Canaylan
View ArticleRe: Perfect Build Surface For PLA?
Only thing I do is wipe it down with Acetone between prints. I run PLA @ 55 and ABS @ 90. After a 10 - 15 degree drop then piece will release from the bed. I have it secured with 3M 468MP Tape. I have...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
Quotenka Picture btw... 4lLPbKn.jpg Is that a webOS HP TouchPad in the background? I was wondering who bought the other one..... :)
View ArticleRe: Help with Rostock parts
Since you claim to be buying quality parts, why are you scrounging eBay for junk steppers? Three NAME BRAND stepper motors with the correct 4 wire plugs (and not the 6-wire ones on eBay) and a...
View ArticleRe: Cherry Pi III Is Available
yes its a webOS TouchPad, but its running Android, I got it on sales for 99$ when HP discontinued them. It's used as a baby monitor now. I've checked the arms, they are all the same, but I think the...
View ArticleRe: Core XY Printer £100.00 Build Cost
I am interested in building one, I like the idea of using wheels on the beams for liner motion. Thanks for the link, I have found most of your other posts there, but I didn't see a forward link to...
View ArticleRe: Cherry Pi III Is Available
If it slams into the bed during a G30 probe, then it sounds like the Z-min endstop switch is either not working or possibly that the spring(s) on the hinged plate are too tight. A few M119 commands...
View ArticleRe: Cherry Pi III Is Available
The endstop work, as it's "open" when not touching and if I "push it" a little it does "triggered". Also, after the slam, it goes up and goes down slowly and then do the calibration. I'll try to...
View ArticleRostock homing problem
Hello, i'm new to 3d printing but i played a bit with prusa i2 and now it was time for me to build the delta. I can't get Home all axes to work don't know why. Only Z axis seems to work fine ( it goes...
View ArticleClik here to view.
Re: Cherry Pi III Is Available
I fixed the "slaming" issue. I can now autocalibrate Seems the CA glue hold strong. I replaced two weak magnet and 3 that wasnt proprely seated. Still having the same issue... I dont know where to...
View ArticleRe: Cherry Pi III Is Available
Hi Sebastien It certainly looks like the arms are unequal, this would include the magnets and the possible warping of the effector. It may also be a carriage that isn't square to the tower. Check the...
View Article