Re: Heated bed on Delta mini
10mm to 12 mm insulation foam ( the kind they use in wall insulation ) works best ... if you access to glass wool ( 5-8 mm ) that works best
View ArticleRe: Mini Kossel wont register endstops
QuoteT3P3 This is a slight modification on Johann's firmware (modifications just for our mini kossel changes) which you can try: [github.com] It works well with our mini kossel kit Cheers Tony I tried...
View ArticleRe: Mini Kossel wont register endstops
Check the pins.h in the think3dprint3d version for the correct endstop in numbers for RAMPS. Also if it wont connect then have you set the baud rate in Repetier to 115200?
View ArticleRe: Mini Kossel wont register endstops
I tried flipping the wiring for the endstops on the RAMPS board, and still got the same result.
View ArticleRe: Mini Kossel wont register endstops
QuoteT3P3 Check the pins.h in the think3dprint3d version for the correct endstop in numbers for RAMPS. Also if it wont connect then have you set the baud rate in Repetier to 115200? The pins.h file...
View ArticleRe: Heated bed on Delta mini
1/4in (5 or 6mm) of cork board works well as insulation. Beware, many cork boards now sold are not solid. Pretty sure this is what I used: [www.target.com]
View ArticleRe: RepRap 3DR Delta printer Released
Hi, My name is Andrea and I have built a 3DR over the last months. I am about finished, now I have FSR auto bed levelling, fully graphic smart display. I printed the parts myself with my Mendel90, a...
View ArticleRe: RepRap 3DR Delta printer Released
Wow Andrea, congratulations and welcome! It's good that you say about the stuttering, I also had noticed that, but I hadn't tracked it down. I'll try what you suggest, and maybe we should start...
View ArticleRe: RepRap 3DR Delta printer Released
@andrea even for me after struggling with a j-head requiring too much force i change the extruder to a mk8 drive wheel which solved the problem to a great extent but too be on a safer side i am going...
View ArticleRe: Heated bed on Delta mini
Ahh cork, that is a conveniant idea. It will be nicely shaped when I cut it alongside my bed. Thanks
View ArticleRe: RepRap 3DR Delta printer Released
today I contacted the tech support at RRW and they have suggested to try a manual extrusion with just the heating block. I started cleaning the hot end by heating it up to 230° and then pushing out...
View ArticleRe: RepRap 3DR Delta printer Released
@payala I checked today the spare nozzle I bought along with the hotend, which should be identical to the one installed... the length of the 0.5 orifice is 1.96mm, so it's out of the specs found on...
View ArticleRe: Mini Kossel wont register endstops
When loading firmware to use with repetier. Use the marlin.ino file instead of the marlin.pde.
View ArticleRe: Mini Kossel wont register endstops
It acts as if the endstops are not working. When you run an M119. Manually trigger the endstops and see if they report triggered when you are holding it. And make sure that on the ramps, the endstops...
View ArticleRe: Mini Kossel wont register endstops
QuoteWildcard It acts as if the endstops are not working. When you run an M119. Manually trigger the endstops and see if they report triggered when you are holding it. And make sure that on the ramps,...
View ArticleRe: Mini Kossel wont register endstops
Awesome! But I don't understand that your M119 reported all three MAX endstops, and that you saw them getting triggered while they were not connected :S Probably just a glitch in the matrix...
View ArticleRe: Heated bed on Delta mini
I was going to use cheap cardboard for my kossel, is that insulating enough or should I upgrade to cork?
View ArticleWhere to mount the extruder on Rostock Mini
I am nearly finished building my 3dprinterczar Rostock delta mini pro, but have no clue how both the acrylic build plate, the arduino/ramps ánd the extruder should be fixed to the construction bottom...
View ArticleRe: Where to mount the extruder on Rostock Mini
Is it possible that you don't need to fix those parts? If I am correct, this youtube channel contains videos of someone building this printer model, and he also leaves those parts unfixed... This is...
View ArticleDelta design considerations/theory
Hi everyone, I'm looking into designing my own small delta Reprap from scratch, mainly for the fun of designing machines. However, I'm a bit at a loss when it comes to details on delta Reprap theory;...
View Article