Re: Marlin Delta Firmware Issue
My printer is printing with Repetier firmware at the moment, looking good! I have made a log of the things I did to get it running, I will post it here when I am done editting and translating!
View ArticleRe: Marlin Delta Firmware Issue
Hey, I am glad you got it working! And I am extremely grateful that you are logging the issues and errors + fixes. and Good News! I have found my Sanguinololu Board! I will have a play on Monday and...
View ArticleRe: Pronterface home issues
All three axis are refusing to home. What do I have to modify in pins.h, I left that one original? I cannot get to pins.h because the tabs at the top of the arduino window go off the screen. Thanks...
View ArticleRe: Cherry Pi III Is Available
Hey Andy, pretty confident the carriages you sent me were the old design; it'd definitely explain the poor fit for me! I also compared to the sketchup you just posted. [attachment 40737...
View ArticleRe: Cherry Pi III Is Available
Hi Guys For clarity the current production version of the Mini V Wheel Carriage for use on KJN Bosch/Rexroth extrusion (as per the Cherry Pi III BOM) is this :- [attachment 40741...
View ArticleRe: Pronterface home issues
You have selected a hardware profile in Configuration.h by setting MOTHERBOARD, pins.h contains the hardware definitions that belong to the selected hardware profile. You use pins.h to tweak the...
View ArticleRe: Marlin Delta Firmware Issue
Well this has made my life a lot harder! My Sanguinololu board doesn't work! It has exactly the same issue as my Ramps 1.4. What the hell is going on?!
View ArticleRe: Marlin Delta Firmware Issue
If you have EEPROM enabled, it can contain corrupted settings. M503 shows you the current settings in EEPROM M502 resets the settings by loading firmware defaults M500 stores the reloaded default...
View ArticleRe: Marlin Delta Firmware Issue
GOD DAMMIT!!! I had a number wrong in the Printer Set-up. I had put 29mm rather than 92mm 29mm is an Impossible value, hence why it crashed when i tried to move it! ARGH!!!
View ArticleRe: Marlin Delta Firmware Issue
Here you have my first version of the Repetier log: Printer type: Kossel mini without probe Firmware version used: Repetier 0.91 Hardware version used: Minitronics 1.1 Used internet resources This is...
View ArticleClik here to view.
Re: Marlin Delta Firmware Issue
Quoteayouden GOD DAMMIT!!! I had a number wrong in the Printer Set-up. I had put 29mm rather than 92mm 29mm is an Impossible value, hence why it crashed when i tried to move it! ARGH!!! Now you point...
View ArticleRe: Marlin Delta Firmware Issue
Yes, my printer is very, very small! And thanks for that log you did! If I get any errors I think it will come very handy! Thanks
View ArticleRe: What Delta Variation?
Just a point about geared extruders. The slop in gears gets multiplied due to bowden setup. I would invest the cash on a set of pulleys and belt and build the extruder around those. You get nearly the...
View ArticleRe: Best way to route the bowden tube?
I prefer the S bend. Putting the extruder at the bottom with a soft bend and a good clamping. Then the final bend at the head. It seems to make sense to me instead of the top of the printer.
View ArticleRe: Pronterface home issues
Quote3D-ES M119 should say "open" when not triggered, it also should not show X_MIN and Y_MIN status. Hi I am currently out of town for the week so I will not get to try fixing the pins.h till this...
View ArticleRe: Cherry Pi III Is Available
Stray from the BoM, pay the consequences! Haha. Lesson learnt. :) Out of interest Andy, what settings do you use to generate your carriages? As in, what % fill etc so that you got a good amount of...
View ArticleRe: What Delta Variation?
Slop in the extruder isn't that big of a deal and is easily accounted for (add a little extra to retraction, done), what do you think we do for bowdens. Slop in your axis drivetrain, is a different...
View ArticleRe: Want to do a "pencil" dry print, but will not do x and y movements after...
lol I knew I should've done that before I asked!! It works!!! Lesson learnt: Firmware disabling won't work if the G-code demands otherwise.
View ArticleRe: Cherry Pi III Is Available
I use 0.3mm layer height and 33% in fill on virtually all my printed parts. The effector, which is the only ABS part, I print at 0.2mm layer height. I use a drop of high viscosity CA to fix the limit...
View ArticleRe: Cherry Pi III Is Available
Thanks for that! Looks like I've got a bit of adjusting to do then.
View Article
