Re: Marlin Delta Firmware Issue
After you home your printer it does not want to move down, have you tried to move it up? Just to see what happens?
View ArticleRe: What Delta Variation?
Hello sheepdog43, what do you think about aluminum extrutions 25x25, do you think I should go bigger?
View ArticleRe: Marlin Delta Firmware Issue
Okay, So when I do G28 then G1 Z300 (Max should be 250) The printer doesn't move but when I send M114, the Z is at 300. Which is shouldn't be! I have attached a screenshot of this.
View ArticleRe: What Delta Variation?
You don't really need 25x25 until you hit about 1000mm or bigger. Before you do that, I would go 20x40 V-slot or Open Rail or similar with a built in track system, it just saves so much hassle and money.
View ArticleRostock 3d printer program error
Hi I have just finished my rostock 3d printer and when I went to download the Marlin software onto the arduino I got an error. It says DELTA_PRINTER_MARLIN_Configuration_h.cpp:731:31: error:...
View ArticleRe: Marlin Delta Firmware Issue
This is so strange... Your printer moves repeatedly to X0, Y0, Z250 when instructed by G28, but it refuses to move when the move is started by G1, but updates Z. What are the differences between a G28...
View ArticleRe: Marlin Delta Firmware Issue
Hmmm, that is a good idea! I won't be able to gain access to the 3D Printer until Monday sadly! I have a few Ideas to try and narrow down what it is. I have a spare Ramps 1.4 shield which I can swap...
View ArticleRe: Rostock 3d printer program error
Hi Tanner! That "Configuration_h.cpp" is a bit strange, I think that that should be "Configuration.h" Are you following a tutorial? A bump in the right direction: - I use Arduino 1.0.5 - I downloaded...
View ArticleRe: Cherry Pi III Is Available
Quotepugzor Hey maso... Did you also encounter the issue that OpenBuilds V Slot is not compatible with the carriage design? I'm finding that there's a fair bit of a gap between the mini V wheels and...
View ArticleRe: Cherry Pi III Is Available
Hi Guys I managed to get hold of a piece of V slot to compare it to the extrusion that I use, Bosch/Rexroth from KJN in the UK [attachment 40592 20140920_092711.jpg] You can clearly see the difference...
View ArticleRe: Cherry Pi III Is Available
Wow, thanks Andy! Without looking at the STLs, what was the modification? How much closer to each other did the wheels move? My guess would have been 3-4mm...
View ArticleRe: Cherry Pi III Is Available
For completeness of the discussion, Misumi 2020 has totally square-cut slots. The Mini-V wheels *barely* have any contact with the inside of the slot, and require a larger mounting plate (or a shim to...
View ArticleRe: Rostock 3d printer program error
Hi 3D-ES I downloaded jcrocholl's version of the software from your link and it worked perfectly. I think the problem was that I did not have the downloaded file, I used copy and paste to get the...
View ArticlePronterface home issues
Hi I have a reprap rostock 3d printer and I have been trying to configure it. I am having issues using pronterface. The problem I am having is that when I hit the "home" it does not move all the axis...
View ArticleRe: Pronterface home issues
Is this when you run the jcrocholl firmware from this thread? Is something restricting the movement of the belt? It sounds like it tries, but just can't get any higher. Are all your endstops...
View ArticleRe: Cherry Pi III Is Available
Quotepugzor Wow, thanks Andy! Without looking at the STLs, what was the modification? How much closer to each other did the wheels move? My guess would have been 3-4mm... You won't need the new rod...
View ArticleRe: Cherry Pi III Is Available
Hmm. Even with the tensioning screw done up fully, there's still around 1-2mm of play between the V slot and one of the wheels (assuming the other wheels are fully in the V slot). That's for me anyway.
View ArticleRe: Pronterface home issues
I am using the jcrocholl firmware. Nothing is restricting the movement of the belts, I can lower it and raise it with the motors manually with no problem, and when I restart it at another location it...
View ArticleRe: Pronterface home issues
Strange! So your situation looks like this: - You click home to initialize the printer - 2 axis move all the way to the endstops - 1 does not move at all, but makes sound - After that, you can move...
View ArticleRe: Cherry Pi III Is Available
Hi Guys I've attached my original Sketchup file for the V wheel carriage. Amend it to suit your needs. Regards Andy
View Article