Quantcast
Channel: Reprap Forum - Delta Machines
Browsing all 20291 articles
Browse latest View live

Re: Cherry Pi III Is Available

That's very possible. They were designed for the Bosch/Rexroth compatible extrusion that I use from KJN in the UK. [attachment 40441 2020drg_small.jpg]

View Article


Geared Nema will not turn

My Rostock Delta mini pro came with a mounted gearbox on the extruder motor. Now, when testing, the motor will only give a smal hick and than is unmovable stuck. When I push the emergency stop, it...

View Article


Re: Marlin Delta Firmware Issue

Hey, I tried Repetier Firmware once and for the life of me I couldn't get it to work!

View Article

Re: Core XY Printer £100.00 Build Cost

Hi, may I ask where you buy your hotend from? thx :)

View Article

Re: Marlin Delta Firmware Issue

Just discovered something very odd! [forums.reprap.org] Could this be the reason why? Thanks

View Article


Image may be NSFW.
Clik here to view.

Re: Geared Nema will not turn

It happened to be the gear set. I dismantled the gear, re assembled and after the 3rd mount attempt, it kept running. Maybe some debris in a gear somewhere.... foto-3.JPG

View Article

Re: Marlin Delta Firmware Issue

What happens when you home twice? I would expect that it goes through the same motions twice, if the motors don't move the second time, it can be a short-circuit... Can you attach a photo of your...

View Article

Re: Marlin Delta Firmware Issue

Here are the images of my Ramps 1.4. Also I can do G28 as many times as I want and it still homes perfectly!

View Article


Re: Marlin Delta Firmware Issue

Your hardware config looks good (to me...) I am going to try Repetier on my Kossel mini this weekend, do you remember what your problems were with Repetier?

View Article


Re: Marlin Delta Firmware Issue

Yea, For some reason, I could not get it to home! I kept on getting this message when i tried to home the machine: Warning:Invalid delta coordinate And nothing moved at all!

View Article

Re: New Own Design Printer 'Cherry Pi'

Could someone run through the settings for cura so I can get my cherry pi lll to print.What printer do I pick on the wizard etc.I have done it once already and the current print job will goto about...

View Article

Re: Cherry Pi III Is Available

Could someone run through the settings for cura so I can get my cherry pi lll to print.What printer do I pick on the wizard etc.I have done it once already and the current print job will goto about...

View Article

Re: Geared Nema will not turn

If it turned without power, it was nothing inside the gearbox and the problem will likely return at some point. It may be a wire problem, which you may have fixed while taking it off and putting it...

View Article


Re: Geared Nema will not turn

Well there is a difference: when turning free, the momentum comes from the outgoing axis, when powered, from the ingoing .... Could that not have had a problem ?

View Article

Re: Geared Nema will not turn

Not likely.

View Article


Re: Cherry Pi III Is Available

QuoteAndyCart That's very possible. They were designed for the Bosch/Rexroth compatible extrusion that I use from KJN in the UK. Fortunately it's only by a mm or two, so it doesn't take too much...

View Article

Re: Cherry Pi III Is Available

I used OpenBuild V-slot too, and for me it was more than a few mm. I was using 10-32 hardware, so that might affect things a bit. But I couldn't even fit the nut and washer in the slot, much less the...

View Article


Re: Cherry Pi III Is Available

Quotemaso I used OpenBuild V-slot too, and for me it was more than a few mm. I was using 10-32 hardware, so that might affect things a bit. But I couldn't even fit the nut and washer in the slot, much...

View Article

Re: Cherry Pi III Is Available

I did find that I had to tighten those carriages down quite a bit. Come to think of it, I had to shave some plastic out of the slot in one of them so that I could get it tight enough. But it really...

View Article

Re: Cherry Pi III Is Available

Quotemaso I did find that I had to tighten those carriages down quite a bit. Come to think of it, I had to shave some plastic out of the slot in one of them so that I could get it tight enough. But it...

View Article
Browsing all 20291 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>