Re: Auto Bed Levelling Switch Not Working
Hey, M119 works perfectly and it says triggered when I press the buttons and they all work independently. My X Min and Y Min are all -1 so thats not the issue. Since my last post I am thinking of...
View ArticleRe: A Bigger Slice Of Pi ...
Nice :) But stop making new changes I want. I cannot keep up:D
View ArticleNozzle size? The effect of it?
I am running a chinese .4mm j-head clone with great results. I have nothing bad to say about the jhead design or the chinese clone. I also do not cool the jhead at all and it is mounted to an home...
View ArticleMini Kossel build with twist
Hey guys, I'm ordering the parts for my first printer build after owning a Da Vinci and Printrbot Metal Simple. I have gone over the options and so far I would like to do linear rails for their...
View ArticleRe: Nozzle size? The effect of it?
I wouldn't go more than 50-75% of your filament diameter for max nozzle size, however that's just a guess. You need some back pressure I would think. As for what to take into consideration, you will...
View ArticleRe: Nozzle size? The effect of it?
I am thinking of 50-60% of the orifice size is doable. However that would require me to run .8mm filament. probably have to ramp up the temps in the 260c range or higher to do so as well as increase...
View ArticleRe: A Bigger Slice Of Pi ...
You are getting pretty close to the dimensions that my CP mutt was built to! (1000mm long columns, 400mm crossbars) Based on my gut feeling with no engineering research to back it up, :) I was...
View ArticleRe: Mini Kossel build with twist
Hi ChrisT88 We have found that the Delrin V roller design works really well and, like the recirculating balls, is much cheaper than the slide. For the electronics a RAMPS is a tried and tested...
View ArticleRe: Mini Kossel build with twist
It has more or less been accepted in Delta circles that all of the floating point math needed to run a Delta at speed is pushing the upper boundary of 8-bit processors. The beauty of the Azteeg X5...
View ArticleClik here to view.
Re: Mini Kossel build with twist
Thanks for the quick replies. I feel the same way about the 8 bit processor on the Delta configuration and I think regular cartesian designs could benefit too. I think for now I'll start with the...
View ArticleRe: Nozzle size? The effect of it?
Quotejaguarking11 I am thinking of 50-60% of the orifice size is doable. However that would require me to run .8mm filament. probably have to ramp up the temps in the 260c range or higher to do so as...
View ArticleRe: Nozzle size? The effect of it?
This is all 1.75mm talk to follow.... Depending on the part, keeping in mind you can have a 0.15mm layer height with most nozzle sizes, the end product could look almost identical with a .3, .4, or .5...
View ArticleRe: Mini Kossel build with twist
I used a printrboard and now have a smoothieboard azteeg x5 mini. For making small changes, the smoothieboard is a lot easier. No more putting jumpers on and off, loading arduino IDE, saving a temp...
View ArticleRe: A Bigger Slice Of Pi ...
2040 for the towers certainly works better at 1M than 2020. If I hold the bottom of the machine and try to twist the top its actually the bottom stepper bases that flex. So far this isn't showing in...
View ArticleRe: Nozzle size? The effect of it?
The reason I went with 1.75mm filament is because its becoming the standard. With a proper drive mechanism its reliable, light and has more options as of today. I think I may just buy a all metal...
View ArticleRe: Mini Kossel build with twist
For cheap RAMPS try here. I've bought about 15 sets now and only once had an issue, a 4988 needed a joint re-soldering. They ship in about two weeks to the UK. [www.aliexpress.com]
View ArticleRe: Rostock problems on the outer regions.
Hi ! Me again :) I've rebuilt the whole thing with magnetjoints... but used to weak magnets so i went back to my original design in wait for stronger magnets... I loosened the plasticjoints and now it...
View Articledelta problem - x, y, and z axis only move positive
I just built my new delta and am having trouble with axis movement. The x, y, and z axis will only move in the positive direction and I can not figure out why. Tried reflashing the firmware and...
View ArticleRe: delta problem - x, y, and z axis only move positive
Use M119 to check your endstops to see if the signal is inverted. If the firmware thinks they are triggered, the towers will only move in one direction using some firmware.....
View ArticleRe: Rostock problems on the outer regions.
Maybe more Microsteps ? Try RADDS. PM me for a Developper Condition if you like...
View Article