Re: RepRap 3DR Delta printer Released
Hello Im building my first 3D printer and i chose 3DR..(yikes) so far so good though its being going ok. got most of my parts from ebay. Here are some pics from my page [instagram.com] [instagram.com]...
View ArticleCherry Pi II Released
Hi All I've just published the latest iteration of my Cherry Pi printer, Cherry Pi II, on Thingiverse (http://www.thingiverse.com/thing:298168) The major changes are :- All electronics and PSU are now...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Okay, I'm much better now. Going back to my post to comment. Basically though, there are 4 wires on my endstop board and I am ignoring everything but the GND and the S and getting better results.
View ArticleClik here to view.
Re: Rostock Mini - Homing Issues (video)
Okay, figured out the issue. My issue was caused by the over complication of the Sainsmart endstops. Here are my exact endstops: [www.sainsmart.com] In that link you will find this image: 4.jpg Notice...
View ArticleClik here to view.
Re: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Andy, Yep, you are right again. I'm using the following Sainsmart endstops and I just needed to choose one of the two GND wires in the middle to connect to my SIG and GND wires on the board. Now I...
View ArticleRe: Cherry Pi II Released
That figures! I just started printing the parts for a Cherry Pi Mk1, and it will be obsolete before I finish it. :( Seriously though, it looks good from the pictures. Did the three force/strain...
View ArticleRe: Kossel Mini on Printrboard
All I had tried was a bunch of different configurations on the E endstop location. So you think I could just go into pins.h and set the E endstop pins as the Z min? Ill have to try that. Ill try that...
View ArticleRe: RepRap 3DR Delta printer Released
Thanks for the video, it saves our time to guess what could be wrong (tu) Richrap provided two kind of carriage, one for LMU and one for bushing. I printed the one for bushing but soon I saw there is...
View ArticleRe: Kossel Mini on Printrboard
Well, I still can't get it to work. I found this section in pins.h #else // Printrboard #define X_STOP_PIN 35 #define Y_STOP_PIN 8 #define Z_MAX_PIN 36 #define Z_MIN_PIN 37 // Use E-STOP for autolevel...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Hi Mike I suspect it's because you don't have the jumpers installed that tell your drivers what micro stepping mode you are using. If you have A4988 drivers and have set your steps per mm in Marlin to...
View ArticleRe: Cherry Pi II Released
Hi. Yes the FSR force sensing resistors are installed and working great. You can see them on one of the Thingiverse images I posted. Cherry Pi II auto calibrates and auto bed levels. Cherry Pi II...
View ArticleRe: Rostock Mini - Homing Issues (video)
Dear Mike (i am not an expert but i'll try) first, is the marlin you'r using the latest one? i found many difference between what i have and urs (i dwl the latest for my delta) there is many things in...
View ArticleRe: Cherry Pi II Released
By switching to a heated build chamber! I am interested in this proposed kit of yours! Would want to scale it up a bit. Do you like the magnetic effectors much more than the traxxas u-joint alternatives?
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
If Sainsmart's RAMPS board is anything like their Megatronics kit, they didn't ship it with DIP jumpers and you will need to buy three for each stepper driver to set the correct micro-stepping rate.....
View ArticleRe: Cherry Pi II Released
QuoteAndyCartI'm sure someone much brighter than me will find a way and then ... Cherry Pi III (:P) I'm putting my money on you figuring it out before they do. Would the sensors read properly if you...
View ArticleRe: NEED HELP !!! ROSTOCK BUILD - WHATS WRONG !!! :(
Here's a post from today, showing the RAMPS board with the micro-stepping jumpers installed: http://forums.reprap.org/read.php?262,336883,339384#msg-339384
View ArticleRe: Cherry Pi II Released
Quote3DRapidClone By switching to a heated build chamber! I am interested in this proposed kit of yours! Would want to scale it up a bit. Do you like the magnetic effectors much more than the traxxas...
View ArticleRe: Cherry Pi II Released
Quotevreihen QuoteAndyCartI'm sure someone much brighter than me will find a way and then ... Cherry Pi III (:P) I'm putting my money on you figuring it out before they do. Would the sensors read...
View ArticleRe: Cherry Pi II Released
QuoteAndyCart A guy called Wing on there has done a fantastic job producing some code for a tiny arduino board that sorts out the major problem with FSR which is balancing the don't trigger with the...
View ArticleRe: RepRap 3DR Delta printer Released
>> @HaDe I saw you also complained about slippage in the spools, how did you solve it? << Guess I wrote about that in the list already but the problem was that the three original length...
View Article