Re: Effector "Rocking"
If you are in EU try these: MP JET Ball Link (Ø7 mm, M3, M3 short) [bigplanes.nl] They are sold assembled and tight. No need for rubber bands. No way I would go with magnetic joints instead of good...
View ArticleRe: Effector "Rocking"
I use the traxxas. I bought them and used springs to take out the slop. I love the ball joints, I think they are the best in my opinion.
View ArticleRe: Rostock calibration
I didn't use belts because I want to use racks and pinion gears then
View ArticleRe: Cherry Pi III Is Available
woohooo ! [www.youtube.com] 10mm cube, is 10mm ! Moving to next print. I also have to ajust my height, since I'm scratching the tape on the first layer! Easy way to do this without recalibratiing the...
View ArticleRe: Cherry Pi III Is Available
okay... Next step : 1) Tight the belt a little more. Seems to have backlash. Some side of the square were a little wavy and my circle are a little oval. 2) Add fans for the ramps and stepper... they...
View ArticleRe: Cherry Pi III Is Available
You may have your stepper drivers dialled too high. I don't even have heat sinks on mine and they are barely warm, I use 4988 with R4 shorted out. The video looks great btw X(
View ArticleRe: Besides Pronterface what is there?
I print almost exclusively from SD. I use Cura to slice. The new version of RH can use the Cura engine though so I might have a play with that.
View ArticleClik here to view.
Re: Effector "Rocking"
Thats what I ended up doing... pressed in the "balls" and used springs - so far so good! 20140815_183940_zps4f90c16a.jpg 20140815_183949_zps44800940.jpg 20140815_183958_zps54c66c1d.jpg What about the...
View ArticleRe: Effector "Rocking"
I'm betting the radius of your rod ends was greater than the radius of the balls. I'm surprised people are glad to switch to traxxas rods, as theoretically they wear out over time and have slop and...
View ArticleRe: Cherry Pi III Is Available
Yeah, I ajusted them, they seems to be more silent now too... didnt try a print, cause I was trying to fine tune the printer. btw... glass just craked... :'( Need to get a new one... I'll get a strong...
View Article3DR Delta printer and Melzi V2.0
Hi everyone :) Just finish mechanical part of build and go to use firmware on Melzi V2.0 and have a strange issue.... My extruder, extrude a 1/5 (or reverse the same) of length given through Printrun....
View ArticleRe: Effector "Rocking"
Different strokes for different folks. Everything needs mateience after awhile and even a magnetic setup can have slop, or may break down after awhile because you have metal on metal or plastic on...
View ArticleRe: Effector "Rocking"
I've never tried the aluminum joints. I guess you would need to check their clearance and experiment. Btw what are dimensions of that machine- looks huge.
View ArticleRe: Cherry Pi III Is Available
Found a mirror to get me back on track, I'm calibrating right now. Hope people didnt think I was buying those to decorate, they are ugly... lol Yesterday, I was looking at heatbed and I think the...
View ArticleRe: Cherry Pi III Is Available
Quotenka Found a mirror to get me back on track, I'm calibrating right now. Hope people didnt think I was buying those to decorate, they are ugly... lol Yesterday, I was looking at heatbed and I think...
View ArticleRe: Cherry Pi III Is Available
yeah, it is... (#define EEPROM_SETTINGS). The settings are staying saved and I see them when I reload the printer, but it just dosent seems to listen to the adjustment I'm making using M666. I'll wait...
View ArticleRe: Cherry Pi III Is Available
Updated : Seems that after the "G30 A", all corner are at 0. And I can removed height size with "M666 Hxxx". Dont konw why it wasnt working before !
View ArticleRe: Cherry Pi III Is Available
I was browing around for stuff to print and I found that... The idea is pretty good. Wonder if we can apply it to the Cherry. [www.thingiverse.com]
View ArticleRe: Effector "Rocking"
I don't use magnets or Traxas. I print 8mm 'cups' in the plastic parts and my rods have 8mm balls on the end. The rods are held in place with a piece of Spectra line and a spring. No backlash or slop...
View Article