Re: Effector "Rocking"
That's is a cool solution. The 3m Di-Noc vinyl wrap looks nice on the printer. Does it release good? My profession is composites—carbon fiber. I built a thick carbon bed for my printer.
View ArticleClik here to view.
Re: Cherry Pi III Is Available
This is more or less what I am using: http://www.thingiverse.com/thing:36813 Cable_Tie_Belt_tensioner_preview_featured.jpg My belt isn't continuous, so the yellow cable ties that they used in the...
View ArticleDelta auto leveling
Now that I finally got my effector tracking true, I'm going to start calibrating. I have been out of the latest advancements in bed autoleveling as Ive primarily been using my I-3 derivative printer...
View ArticleRe: Delta auto leveling
I believe that the available probe options that are working today are: Allen wrench, as on the Kossel. Force Sense Resistors (FSR), using JohnSL's adapter board, an Adafruit Trinket, or wired to your...
View ArticleRe: Delta auto leveling
This would be under the proximity sensors, but the Hall-o effect sensor z-probe (others would be optical sensor z-probe) is one that I implemented on my printer when I first got it up and running. The...
View ArticleRe: Delta auto leveling
I just wasnt sure whats out there - I was planning on manually calibrating but after I saw the "hopping" videos for calibration I figured Id ask if its worth the extra time NOW as im printing my...
View ArticleRe: Delta auto leveling
The johann mini kossel version along with the other versions don't have servos and doing add too much weight. I originally wanted to use autocalibration because I felt that it would be a great way to...
View ArticleRe: Cherry Pi III Is Available
Quotemaso [attachment 36189 fanfit.jpg] I can also confirm that the fan will work when it's that close to the magnet. Spins like a dream! I am using 1/2 inch (12.7mm) spherical magnets, and just...
View ArticleRe: Delta auto leveling
I just re-mounted the heated bed on my printer after an effector/carriage change without the FSR's connected. I spent more time trying (unsuccessfully) to get auto-calibration working than I did...
View ArticleRe: Cherry Pi III Is Available
Quotevreihen Quotemaso [attachment 36189 fanfit.jpg] I can also confirm that the fan will work when it's that close to the magnet. Spins like a dream! I am using 1/2 inch (12.7mm) spherical magnets,...
View ArticleRe: Delta auto leveling
I' a great believer in keeping it simple. The hinged hot end mount and microswitch combination in my Cherry Pi effector just works (:P)
View ArticleRe: Effector "Rocking"
The carbon fibre effect vinyl is o.k. It works better on an acrylic rather than a glass bed. For glass I keep going back to a glue stick (Pritt Stick here in the UK) it just works. Looks messy though!...
View ArticleInjection Molded Parts - Delta
I have and injection molding machine. I was thinking about making some standard parts for Delta 3D Printers. I wanted to get a sense of the level of interest and recommendations on which designs/parts...
View ArticleRe: Cherry Pi III Is Available
So I have about 20 hours of print now, I can say it's working fine. I managed to fix most of the problems I found. I also did a 8 hours non-stop printing as a stress test to the printer. Everything...
View ArticleRe: Cherry Pi III Is Available
Quotenka So I have about 20 hours of print now, I can say it's working fine. I managed to fix most of the problems I found. I also did a 8 hours non-stop printing as a stress test to the printer....
View ArticleRe: 3DR Delta printer and Melzi V2.0
What is the extruder steps per mm set to in the firmware and/or EEPROM? It sounds like this is set too low. adavidm
View ArticleRe: Cherry Pi III Is Available
They are tooth to tooth, but I think they are not tight enough into the "slot". The lower one seems be okay, but not the upper one. If I pull very hard, I see them slip (even if the bolt is tight). I...
View ArticleRe: 3DR Delta printer and Melzi V2.0
I currently don't know because I'm looking at this from the phone, but this got me thinking; shouldn't we put information like this, together with slic3r config, calibration, etc in a wiki page so...
View ArticleStrange behaviour of G29 command
I have built and calibrated a 3DR printer. after a while I got interested into auto bed levelling using FSR so I bought 3. I connected them to RUMBA ZMIN endstop, configured the endstop to use the...
View Article