Re: Injection Molded Parts - Delta
I would think that you would have no problem getting rid of 2020 Kossel top and bottom brackets, although many people still want the 1515 profile.....
View ArticleRe: Cherry Pi III Is Available
I like that tensioner for a new carriage design. Regarding the belts going slack, I noticed that my second printer's belts were stretching on the first few prints. It may just be normal with some belt...
View ArticleRe: Injection Molded Parts - Delta
Why limit this survey to Delta shaped printers? I think that for lots of designs, a casing for the standard 8mm liniari bearing is interesting. With a flat side and 2 holes bolting the bearing to any...
View ArticleRe: Cherry Pi III Is Available
Quotenka They are tooth to tooth, but I think they are not tight enough into the "slot". The lower one seems be okay, but not the upper one. If I pull very hard, I see them slip (even if the bolt is...
View ArticleRe: Cherry Pi III Is Available
Awww... must be that. Mine came from AliExpress, might be cheap. I should have ordered those from Openbuild at the same time of the mini wheel. btw, I fixed the problem, I just placed a small paper...
View ArticleRe: 3DR Delta printer and Melzi V2.0
Thank you so much, I check the data there...seems to be so low - just like you say! I go to adjust there...after end i'll call the results ;)
View ArticleRe: Cherry Pi III Is Available
Definitely must be various thicknesses of GT2 belt. My belts need to be forced into the slot on the rod carrier. To the point where the machine will operate ok without the screw in the belt loop. The...
View ArticleRe: Injection Molded Parts - Delta
Delta frame parts are deceivingly complex in regards to injection molding, remember, they were designed for 3d printing, not injection molding. We've been looking into injection molding the Griffin...
View ArticleRe: Injection Molded Parts - Delta
To put it all into perspective along with what Sheepdog said, we uploaded a Griffin Pro lower connector to ProtoMold to see how much it would come back at for single mold. It was over $15,000 for just...
View ArticleRe: Cherry Pi III Is Available
Hi Guys I've added some new, detail shots to Thingiverse along with some updated .stl files and a guide to how many T nuts are required in the base of the printer. [www.thingiverse.com] Regards Andy
View ArticleRe: Cherry Pi III Is Available
nice job! I like the look of the new spool holder ! The cable management thing look very usefull ! :) I also noticed that you doubled the cable to the spring. I only have one per side, work fine but I...
View ArticleRe: Cherry Pi III Is Available
Quotenka I got those Belt ( [www.aliexpress.com] ), just FYI. Same as the ones i got
View ArticleRe: RepRap 3DR Delta printer Released
Update about my last situation..... The problem with extruder is resolved. Main mechanical problems are resolved to, but..... When i begin to print, on brim and on first level everything going fine...
View ArticleRe: Injection Molded Parts - Delta
If you shop around and use a short-run steel mold, the cost can be significantly cheaper. Not super cheap though.
View ArticleRe: Injection Molded Parts - Delta
I am actually planning to use aluminum mold. Even less $s.
View ArticleRe: Injection Molded Parts - Delta
Maybe it is aluminum I am thinking of. It's the ones used for prototypes/short run products.
View ArticleWhich grease on the rods ?
I would like to know what is the best way to grease the rods of my Rostock Delta Mini Pro. I remember tat my Cartesian Orca sometimes got blocked because the ptfe spray wa not coping with the heat...
View ArticleRe: Strange behaviour of G29 command
I have the same problem :). Cause is that you have firmware that does not have autolevel configured for delta machine. As far as I can tell, this firmware has support. If you check function...
View Article